ReferenceDesignLibrary

Designs (277)

277 Results - Page 1/28 |< < 1 2 3 4 5 > >|

LM3464EVAL: 4 Channel @ 350 mA/chan, 12~80V in

Manufacturer: Texas Instruments

This evaluation board demonstrates the high power efficiency and outstanding output current accuracy of the LM3464A typical application circuit. With four LED strings connected, the total output power is about 50W. The schematic, bill of material and PCB layout drawing of the LM3464A evaluation board are provided in this document.

View Design

LM3450AEV230V30: 700mA @ 45V Max, 180 ~ 265 VAC

Manufacturer: Texas Instruments

The LM3450A evaluation board is designed to provide an AC to LED solution for a 30 W LED load. Specifically, it takes an AC mains input and converts it to a constant current output of 700 mA for a series string of 1 to 13 LEDs (maximum LED stack voltage of 45 V). There are two assembly versions designed to operate from two different nominal AC input voltages, 120 VAC or 230 VAC.

View Design

LM3401-MR16DEMO: 1A @ 6.2V Max, 12VAC, MR16

Manufacturer: Texas Instruments

This design was developed to minimize the current spikes coming out of an electronic transformer to less than 5A, which is a typical transformer rating, when driving an LED MR16 circuit. The off the shelf LED MR16 solutions exhibit spikes that significantly exceed a transformers maximum rated output current which will degrade the reliability of the transformer and reduce its operating lifetime. T…

View Design

TPS61150EVM-150: 15mA x2 @ 17.4V Max, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

LM3404HVEVAL: 1A @ Vin Max, 6 ~ 75V in

Manufacturer: Texas Instruments

The LM3404HV circuit and BOM have been designed to provide a constant forward current of 1.0A to a single LED with a forward voltage of approximately 3.7V from an input of 48V ±10%. Over the input voltage range of 6V to 75V the average LED current, IF, is 1.0A ±10%, the ripple current, ΔiF, will not exceed 400 mAP-P, and the switching frequency is 200 kHz ± 10%.

View Design

STEVAL-ILL016V2: 350mA, 700mA, 1A @ 40V Max, TRIAC

Manufacturer: STMicroelectronics

This application note presents a low-cost driver for LEDs that is compatible with TRIAC phase-control dimmers. The design gives luminaire manufacturers a low-cost, commonly available dimming option for home fixtures. A side benefit is that, when not wired to a dimmer, the unit's power factor is over 0.9. The design is based on the L6562A transitionmode PFC controller driving a single stage PFC-fl…

View Design

EVL130W-STRLIG(1): 48V @ 2.7A, 85 ~ 305 VAC

Manufacturer: STMicroelectronics

* For Constant Current, the board must be modified as described on page 8 of the user guide. * Streetlight applications require that the power supply designed to power an LED lamp must have high efficiency and at least an equivalent lifetime in order to guarantee maintenance-free operation during the life of the LED.

View Design

STEVAL-ILL010V1: 350mA @ 20V Max, 8 ~ 30V in

Manufacturer: STMicroelectronics

This evaluation board is designed around an L6902D-based DC-DC converter with dimming interface. The board implements both of two well known dimming methods: - Analog current control - Average current control by PWM

View Design

LM3409HVEVAL: 1.5A @ 42V Max, 48V in

Manufacturer: Texas Instruments

This evaluation board showcases the LM3409HV PFET controller for a buck current regulator. It is designed to drive 12 LEDs (VO = 42V) at a maximum average LED current (ILED = 1.5A) from a DC input voltage (VIN = 48V). The switching frequency (fSW = 400 kHz) is targeted for the nominal operating point, however fSW varies across the entire operating range.

View Design

NCP3065D1SLDGEVB: 0.35, 0.7, or 1A @ 23V Max, 8 ~ 20V in

Manufacturer: ON Semiconductor

The NCP3065 is a monolithic switching regulator designed to deliver constant current for powering high brightness LEDs. The device has a very low feedback voltage of 235 mV (nominal) which is used to regulate the average current of the LED string. In addition, the NCP3065 has a wide input voltage up to 40 V to allow it to operate from 12 Vac or 12 Vdc supplies commonly used for lighting applicati…

View Design
277 Results - Page 1/28 |< < 1 2 3 4 5 > >|