Molexが提供する63813-1500 Instr. Sheetのデータシート

Products Series No 19417-0011 1 9417-0024 19417-0025 19417-0026 19417-0027 19417-0028 19417-0029 1 9417-0030 19417-0031 19417-0032 19417-0033 19417-0034 19417-0047 1 9417-0048 19417-0049 19417-0050 19417-0051 19417-0052 19417-0053 1 9417-0054 1 9420-0001 1 9420-0002 19420-0003 19420-0004 19420-0007 19420-0008 1 9420-0009 1 9420-0010 19420-0011 19420-0012 1008 33000-0001 33000-0002 33000-0003 33000-0004 33000-1001 33000-1002 33000-1 003 33000-1 004 33001-2003 33001-2004 33001-2005 33001-2006 33001-2021 33001-2022 33001-2023 33001-3003 33001-3004 33001-3005 33001-3006 33001 -3021 33001-3022 33001-3023 33001-4001 33001-4002 33001-4003 33001-4005 33001-4021 33001-4022 33001-4023 33001-5001 33001-5002 33001-5003 5023 33011-0002 3301 1-0004 33011-0006 33011-0008 33011-1002 33011-1004 33011-1006 33011-1008 33011-2001 33011-2002 33011-2003 33011-2004 33011-3001 3301 1-3002 33011-3003 33011-3004 33012-2001 33012-2002 33012-2003 33012-2004 33012-2021 33012-2022 33012-2023 33012-3001 33012-3002 33012-3003 33012-3004 33012-3021 33012-3022 33012-3023 34750-0001 34750-0002 34750-0003 34750-0004 34750-1001 34750-1002 34750-1 003 34750-1 004 34081-2003 34081 -2004 34051-2005 34051-3003 34051-3004 34051-3005 34081-4001 34081 -4002 34051-4003 34051-5001 34051-5002 34051-5003 3001 3002 3003 34780-0001 34780-0002 34750-0003 34750-0004 34750-1001 34750-1002 34780-1 003 34780-1 004 Ma1e Termmals, 14-22 AWG
63813-1500 Extractor Tool
Order No: ATS-638131500 Release Date: 04-02-03 UNCONTROLLED COPY Page 1 of 4
Revision: J Revision Date: 04-06-11
Extractor Tool
Application Tooling
Specification Sheet Order No. 63813-1500
SCOPE:
The 63813-1500 Extraction Tool is used on several different connector series. See below.
Product List
Products:
Terminal
Series No
Description Terminal Order Number
19417 MX150L™
Male Terminals,14-22 AWG
19417-0011 19417-0024 19417-0025
19417-0026
19417-0027
19417-0028
19417-0029 19417-0030 19417-0031
19417-0032
19417-0033
19417-0034
19417-0047 19417-0048 19417-0049
19417-0050
19417-0051
19417-0052
19417-0053 19417-0054
19420 MX150L™
Female Terminals, 14-22 AWG
19420-0001 19420-0002 19420-0003
19420-0004
19420-0007
19420-0008
19420-0009 19420-0010 19420-0011
19420-0012
31296 MX150™
Male Terminals, 14-22 AWG 31296-0004 31296-0008 31296-1004
31296-1008
33000 MX150™
Male Terminals, 14-22 AWG
33000-0001 33000-0002 33000-0003
33000-0004
33000-1001
33000-1002
33000-1003 33000-1004
33001 MX150™
Female Terminals, 14-22 AWG
33001-2003 33001-2004 33001-2005
33001-2006
33001-2021
33001-2022
33001-2023 33001-3003 33001-3004
33001-3005
33001-3006
33001-3021
33001-3022 33001-3023 33001-4001
33001-4002
33001-4003
33001-4005
33001-4021 33001-4022 33001-4023
33001-5001
33001-5002
33001-5003
33001-5005 33001-5021 33001-5022
33001-5023
33011 MX150™
Male Terminals, 14-22 AWG
33011-0002 33011-0004 33011-0006
33011-0008
33011-1002
33011-1004
33011-1006 33011-1008 33011-2001
33011-2002
33011-2003
33011-2004
33011-3001 33011-3002 33011-3003
33011-3004
33012 MX150™
Female Terminals, 14-22 AWG
33012-2001 33012-2002 33012-2003
33012-2004
33012-2021
33012-2022
33012-2023 33012-3001 33012-3002
33012-3003
33012-3004
33012-3021
33012-3022 33012-3023
34750 MX150™
Male Terminals, 14-22 AWG
34750-0001 34750-0002 34750-0003
34750-0004
34750-1001
34750-1002
34750-1003 34750-1004
34081 MX150™
Female Terminals, 14-22 AWG
34081-2003 34081-2004 34081-2005
34081-3003
34081-3004
34081-3005
34081-4001 34081-4002 34081-4003
34081-5001
34081-5002
34081-5003
34083 MX150™
Female Terminals, 14-22 AWG 34083-2001 34083-2002 34083-2003
34083-3001
34083-3002
34083-3003
34780 MX150™
Female Terminals, 14-22 AWG
34780-0001 34780-0002 34780-0003
34780-0004
34780-1001
34780-1002
34780-1003 34780-1004
34781 MX150™
Male Terminals, 14-22 AWG 34781-0004 34781-1004
34782 MX150™
Male Terminals, 14-22 AWG 34782-0001 34782-0002 34782-0003
34782-1001
34782-1002
34782-1003
Series No 1000 1100 Female‘ 22-26 AWG 1000 1100 Female‘ 22-25 AWG 05—70-0056 05-70—0057 08-70-0055 08-70-0059 39-00-0155 39-00-0159 39—00-0387 39-00—0388 39-00-0359 39-00-0390 39-00-0442 87-00-0569 87—00-0589 minal 8300 i[ 445-“ ‘14 a \\ “Ex?*lo~q‘= __ ‘ \\ 44.5mm 5°“ For19417 19420 33001 33012 34750 34780 34081 and 34083 Terminal Series: For 31296 33000 33011 34781 and 34782 Series:
63813-1500 Extractor Tool
Order No: ATS-638131500 Release Date: 04-02-03 UNCONTROLLED COPY Page 2 of 4
Revision: J Revision Date: 04-06-11
Screw
Driver Slot
Terminal Release
Service Hole
Service
Tool
Terminal
Series No
Description Terminal Order Number
35464 PT Bulb Socket,
AVSS 0.50~0.85mm² 35464-8000
501647
2.00mm (.079") Pitch iGrid™
Wire-to-Board,
Female, 22-26 AWG
501647-1000
501647-1100
501648
2.00mm (.079") Pitch iGrid™
Wire-to-Board,
Female, 22-28 AWG
501648-1000
501648-1100
5103 SPOX™ Crimp Terminal
22-28 AWG
08-70-0056 08-70-0057 08-70-0058
08-70-0059
39-00-0188
39-00-0189
39-00-0387 39-00-0388 39-00-0389
39-00-0390
39-00-0442
87-00-0569
87-00-0589
59323 Wire to Motor connector Terminal
59323-8000 59323-8100 59323-8200
59323-8300
The above chart is a partial list of the product order
numbers and their specifications this tool is designed
to run. Updates to this list are available on
www.molex.com.
DESCRIPTION:
Extraction Tool is used on extract terminals from
several different connector series.
It is 67.6mm (2.66 in.) long by 6.35mm (.25 in.)
diameter, and weight about 0.03kg (1 oz.).
See Figure 1.
OPERATION:
For 19417, 19420, 33001, 33012, 34750, 34780, 34081,
and 34083 Terminal Series:
SEALED RECEPTACLE ASSEMBLY-
SERVICEABILITY
1. Return the TPA to the pre-lock position.
Use the Standard Screwdriver to return the TPA to
pre-lock.
Listen for the loud audible” click”.
2. Release the terminal from the connector assembly.
Insert and drive forward (0.9 to 1.0mm) diameter
the service tool to release terminal.
Pull the terminal from the rear of the connector.
For 31296, 33000, 33011, 34781, and 34782 Series:
SEALED BLADE ASSEMBLY-SERVICEABILITY
1. Return the TPA to the pre-lock position
Use the Standard Needle Nose Pliers to return
the TPA to pre-lock.
Listen for the loud audible”click”.
23.1mm
0.91”
44.5mm
1.75”
67.6mm
2.66”
Figure 1
a )MC For 501647 501648 and 5103 Terminal Series:
63813-1500 Extractor Tool
Order No: ATS-638131500 Release Date: 04-02-03 UNCONTROLLED COPY Page 3 of 4
Revision: J Revision Date: 04-06-11
Needle Nose
Pliers
Service Holes
Service Tool
Terminal
Release
Service Tool
LOCKING TAB
OF TERMINAL
WIRE
Figure 2
EXTRACTOR
TOOL
LOCKING TAB
PUSHED DOWN
TERMINAL
HOUSING
EXTRACTOR
TOOL
180°
°°
°
Disoriented
Terminal
90°
°°
°
Disoriented
Terminal
2 Release the terminal from the connector assembly.
Insert and drive forward (0.9 to 1.0mm)
diameter the service tool to release terminal.
Pull the terminal from the rear of the connector.
TERMINAL INSTALLATION
Terminal Orientation Feature
This is the Terminal orientation at the matte seal
grommet cap.
OPERATION:
For 501647, 501648, and 5103 Terminal Series:
Individual terminals may be extracted from the housing using this Tool.
1. Push the terminal and the wire forward in the arrow direction before using this Tool. Insert the Tool into the
slot above the locking tang of the terminal. Push the tool down until the locking tang is even with the rest of
the terminal. This will free the terminal from the housing.
2. Holding the wire and the tool together, pull the wire back through the connector slot in the arrow direction
as shown in Figure 2.
For 59323 Terminal Series: For 34564 Terminal Series AND FULL THRU / i ‘ r i \1 \
63813-1500 Extractor Tool
Order No: ATS-638131500 Release Date: 04-02-03 UNCONTROLLED COPY Page 4 of 4
Revision: J Revision Date: 04-06-11
Figure 5
EXTRACTOR TOOL
HOUSING
WIRE
PUSHED DOWN
AND PULL THRU
TERMINAL
PUSH IN
TERMINAL
AND WIRE
TERMINAL
EXTRACTOR TOOL
Figure 3
EXTRACTOR
TOOL
TERMINAL
HOUSING
POCKET
Figure 4
WIRE
HOUSING
EXTRACTOR TOOL
TERMINAL
EXTRACTOR TOOL
For 59323 Terminal Series:
Individual terminals may be extracted from the housing
using this Tool.
1. Insert the tip of the Extractor Tool into the end of
the pocket of the housing. Push the tool down until
it stops.
2. The Latch on the housing will open and then release the terminal. Pull the crimped terminal out by the wire
in the direction shown. See Figure 3 and 4.
For 34564 Terminal Series:
1. Push the terminal and wire forward in the arrow direction before using the Extractor Tool.
2. Insert the tip of the Extractor tool below the seal and terminal into the hole of the connector housing.
3. Gently push the tool under the terminal until the wings of the terminal lift up and out of the slot.
4. Using an eraser end of a pencil push down on the top of the terminal.
5. Pull the terminal and wire out of the hole. See Figure 5.
Molex does not offer repair parts for this tool due to the inexpensive nature of the tool.
http://www.molex.com