NorComp Inc.が提供する971 Series Assembly Instrのデータシート

DESCRIPTION. BACKSHELL ASSEMBLY INSTRUC110N © ©© % CABLE WITHOUT SHIELD OR GROUND JACKSCREW STRAIN RELIEF RECESS E3©IH§ @©I]IIII @LDAN? PLASTIC ITEM No. 2 & 3 ASSEMBLY INSTRUCTIONS: 1. Z. w.» . PLACE THE OTHER HALF OF THE PLASTIC HOOD INTO PREPARE CABLE AS REQUIRED TO ASSEMBLE TO THE CONN ECTOR CHOOSE THE STRAIN RELIEF HALVES THAT MOST CLOSELY MATCH THE CABLE OID AND PLACE ONE INTO EACH RECESS. THEY DO NOT NEED TO BE MATCHING HALVES PLACE THE CABLE INTO THE STRAIN RELIEF IN ONE HALF OF THE PLASTIC HOOD. ENSURE THE CABLE IS PRESSED INTO THE STRAIN RELIEF PIECE SNAP THE JACKSCREWS INTO POSITION PLACE AND “GHTEN TOGETHER WITH THE ASSEMBLY SCREWS AND NUTS "*SEE PAGES 3 AND 4 FOR THE 50 POSITION DIE CAST ASSEMBLY INSTRUCTIONS’M N: THESE DRAWINGS AND SPECIFICATIONS DRAWN: DATE: ARE THE PROPERTY OF NorComp AND C SMITH 03-21-06 SHALL NOT BE REPRODUCED, COPIED ' OR USED 5 THE BASIS EoR THE CHECKED: DATE: MANUFACTURE OF SALE OF APPARATUS X WITHOUT WRITTEN PERMISSION. N.T.S. 1 4 0 N O rCO m p m "°' BACKSHELL - 971 SERIES SCALE: SHEL‘I or REV
DESERT PTION. BACKSHELL ASSEMBLY INSTRUC110N IE CASTE MEI'ALIZED PLASTIC STRAIN RELIEF RECESS GROUND WIRE RECESS FIG. 2 ITEM No. 2, 3 & 4 "'SEE PAGES 3 AND 4 JACKSCREW FOR THE 50 POSITION DIE CAST ASSEMBLY INSTRUCTIONSW‘ FIG. 3 ASSEMBLY INSTRUCTIONS: 1. PREPARE CABLE AS REQUIRED TO ASSEMBLE TO THE CONNECTOR 2. CHOOSE THE STRAIN RELIEF HALVES THAT MOST CLOSELV MATCH THE CABLE O/D. THEY DO NOT NEED TO BE MATCHING HALVES 3. WRAP THE SHIELD/GROUND AROUND THE STRAIN RELIEF AS IN FIG. 2 OR FIG. 3 AND AS OUTLINED BELOW 4. PLACE THE CABLE ASSEMBLY/STRAIN RELIEF INTO THE APPROPRIATE RECESS IN ONE HALF OF THE DIE CAST HOOD. ENSURE THE STRAIN RELIEF IS PRESSED INTO THE STRAIN RELIEF RECESS AREA 5. SNAP THE JACKSCREWS INTO POSITION 6. PLACE THE OTHER HALF OF THE DIE CAST HOOD INTO PLACE AND TIGHTEN TOGETHER WITH THE ASSEMBLY SCREWS FOIL CABLE 1. INSERT THE GROUND WIRE THROUGH HOLE IN ONE HALF OF THE STRAIN RELIEF AS SHOWN IN FIG 1. ASSEMBLE THE TWO HALVES OF THE STRAIN RELIEF AROUND THE CABLE MAKING SURE THAT THE CABLE INSULATION RUNS THROUGH THE FULL LENGTH OF THE STRAIN RELIEF, THEN COMPLEI'E AS IN FIG 2 2. LOOP THE GROUND WIRE AROUND THE GROUND WIRE RECESS AS SHOWN 3. PLACE THE ASSEMBLY INTO THE LOWER HALF OF THE HOOD MAKING SURE THAT THE GROUND WIRE IS SHOWING FROM UNDER THE CONTACT AREA OF THE STRAIN RELIEF ASSEMBLY AS IN FIG 2 4. THE GROUND WIRE CAN BE INSUMTED AND EXTENDED TO A CONTACT ON THE CONNECTOR IF REQUIRED BRADED CABLE 1. FOR HEAVILV BRAIDED CABLE, PIGTAIL THE BRAID INTO TWO BRAIDSV AND BRING IT BACK OVER THE ASSEMBLED STRAIN RELIEF. SEE FIG 3 2. FOR LIGHT BRAIDED CABLE. PIGTAIL THE BRAID INTO ONE BRAID, AND BRING IT BACK IN ONE DIRECTION ONLY 3. SLOT THE ASSEMBLY INTO THE HOOD AND COMPLETE THE HOOD ASSEMBLY DIE CAST & METALIZED SHALL NoT BE REPRODUCED, COPIED THESE DRAWTNGS AND SPECIFTCATIONS DRAWN: DATE: ® ARE THE PROPERTY OF NorComp AND C. SMITH 03-21-06 OR USED 5 THE BASIS EoR THE CHECKED: DATE: MANUFACTURE OF SALE OF APPARATUS X ‘MTHOUT WRHTEN PERM‘SS‘ON. PLASTIC E3©EEU§ @©M@MAMT N.T.S. 2 4 0 N O rCO m p m "°' BACKSHELL - 971 SERIES SCALE: SHEET or REV
971 SERIES 50 PIES DIE CAST COVER HOOD SHORT INSERT EASE HOOD B THUMB /7\[ LONG / INSERT ITEM No. 3 EB©Efl§ @©IIIU@MIAINIT ASSEMBLY INSTRUCTIONS. . PRE’ARE CABLE BIDS. CONNECT TO CONNECTOR . SELECT CORRECT INSERT SIZE FOR CABLE BEING USED, PLACE LONG INSERT INTO RECESS AREA OF BASE HOOD PLACE SHORT INSERT INTO RECESS OF COVER HOOD PLACE CABLE INTO INSERT IN BASE HOOD. USING EITHER THE FLAT OR CURVED STRAIN REuEF (OR BOTH), CLAMP THE CABLE MAKING SURE THE JACKET IS BELOW THE STRAIN RELIEF IF CABLE IS SHIELDED, FOLD SHIELD AND/OR GROUND WIRE BACK UNDER STRAIN RELIEF. CUT OFF ANY EXCESS WIRE So IT DOES NOT S‘nCK OUT OF THE STRAIN RELIEF PLACE THE THUMBSCREWS INTO THE BASE HOOD PLACE THE COVER HOOD ON TOFI OF THE BASE HOOD. MAKING SURE NO WIRES ARE PINCHED . HOLDING THE HOODS TOGETHER. SCREW THE TWO HOOD SEC‘nONS TOGETHER USING THE SCREWS PROVIDED SHIELD AND/OR GROUND ITEMND.2&6 ITEMNo.4&5 DIE CAST ®© INI©IIT §©AILE Ffi©MI @MWIILNI@ THESE DRAWINGS AND SPECIFICATIONS ARE DRAWN: DATE: THE PROPERTV OF Norcomp AND SHALL NOT M. SIGMON 04-26-12 BE REPRODUCED, COPIED OR USED As THE BASIS FOR THE MANUFACTURE OF SALE OF CHECKED: DATE: APPARATUS WITHOUT WRmEN PERMISSION. SCALE: SHEEI' OF REV N.T.S. 3 4 0 o r o m BACKSHELL - 971 -O50-030R1 21
DESCRIPTION. KIT HARDWARE , 971 SERIES , SD FEIS T DIE CAST a 0va In 15.00] I: 0.551 In 14.00] a run IIa 12.501 Ia was In mm] [Ml [$91) 0941094 ( ( \ LT‘ \ K J IJ—l o o o o > < a="" '="" o="" o="" o="" plastic="" inserts="" aég="" _="" g-dt="" curved="" strain="" strain="" relief="" housing="" relief="" screw="" screw="" die="" cast="" ®©="" [n]©'fr‘="" §©ajle="" ffi©mi="" @mwijenj@="" r="" i="" these="" drawings="" and="" specifications="" are="" drawn:="" date:="" the="" property="" of="" norcomp="" and="" shall="" not="" m.="" sigmon="" 04-26-12="" be="" reproduced,="" copied="" 0r="" used="" as="" the="" basis="" for="" the="" manufacture="" of="" sale="" of="" checked:="" date:="" apparatus="" wrrhout="" wrmen="" permission.="" scale:="" sheer="" of="" rev="" e3©efl§="" @©mdlhainit="" nofcomp="" fizgii'hell-4971-olo-osom;="">