Microchip Technologyが提供するPIC16(L)F183xx Briefのデータシート

Q MICROCHIP
2014-2016 Microchip Technology Inc. DS40001744C-page 1
PIC16(L)F183XX
Description
PIC16(L)F183XX microcontrollers feature Analog, Core Independent Peripherals and communication peripherals,
combined with eXtreme Low Power (XLP) for a wide range of general purpose and low-power applications. The
Peripheral Pin Select (PPS) functionality enables pin mapping when using the digital peripherals (CLC, CWG, CCP,
PWM and communications) to add flexibility to the application design.
Core Features
C Compiler Optimized RISC Architecture
Only 49 Instructions
Operating Speed:
- DC – 32 MHz clock input
- 125 ns minimum instruction cycle
Interrupt Capability
16-Level Deep Hardware Stack
Up to Four 8-Bit Timers
Up to Three 16-Bit Timers
Low-Current Power-on Reset (POR)
Configurable Power-up Timer (PWRTE)
Brown-out Reset (BOR) with Fast Recovery
Low-Power BOR (LPBOR) Option
Extended Watchdog Timer (WDT) with Dedicated
On-Chip Oscillator for Reliable Operation
Programmable Code Protection
Memory
Up to 28 KB Program Flash Memory (PFM)
Up to 2 KB Data SRAM Memory
256B of EEPROM Data Flash Memory (DFM)
Direct, Indirect and Relative Addressing modes
Operating Characteristics
Operating Voltage Range:
- 1.8V to 3.6V (PIC16LF183XX)
- 2.3V to 5.5V (PIC16F183XX)
Temperature Range:
- Industrial: -40°C to 85°C
- Extended: -40°C to 125°C
eXtreme Low-Power (XLP) Features
Sleep mode: 40 nA @ 1.8V, typical
Watchdog Timer: 250 nA @ 1.8V, typical
Secondary Oscillator: 300 nA @ 32 kHz
Operating Current:
- 8 uA @ 32 kHz, 1.8V, typical
- 37 uA/MHz @ 1.8V, typical
Power-Saving Functionality
Doze mode: Ability to run the CPU core slower
than the system clock used by the internal
peripherals
Idle mode: Ability to put the CPU core to sleep
while internal peripherals continue operating from
the system clock
Sleep mode: Lowest Power Consumption
Peripheral Module Disable: Peripheral power
disable hardware module to minimize power
consumption of unused peripherals
Digital Peripherals
Configurable Logic Cell (CLC):
- Up to four CLCs
- Integrated combinational and sequential logic
Complementary Waveform Generator (CWG):
- Rising and falling edge dead-band control
- Full-bridge, half-bridge, 1-channel drive
- Up to two CWGs
- Multiple signal sources
Up to Four Capture/Compare/PWM (CCP)
modules
PWM: Two 10-bit Pulse-Width Modulators
Numerically Controlled Oscillator (NCO):
- Precision linear frequency generator (@50%
duty cycle) with 0.0001% step size of source
input clock
- Input Clock: 0 Hz < FNCO < 32 MHz
- Resolution: FNCO/220
Serial Communications:
- SPI, I2C, EUSART
- RS-232, RS-485, LIN compatible
Data Signal Modulator (DSM):
- Modulates a carrier signal with digital data to
create custom carrier synchronized output
waveforms
Full-Featured, Low Pin Count Microcontrollers with XLP Product Brief
PIC16(L)F183XX
DS40001744C-page 2 2014-2016 Microchip Technology Inc.
Peripheral Pin Select (PPS):
- I/O pin remapping of digital peripherals
Up to 18 I/O Pins:
- Individually programmable pull ups
- Slew rate control
- Interrupt-on-change with edge-select
- Input level selection control (ST or TTL)
- Digital open-drain enable
Analog Peripherals
10-Bit Analog-to-Digital Converter (ADC):
- Up to 17 external channels
- Conversion available during Sleep
• Comparator:
- Up to two comparators
- Low and High-Speed modes
- Fixed Voltage Reference at inverting/
noninverting input(s)
- Comparator outputs externally accessible
5-Bit Digital-to-Analog Converter (DAC):
- 5-bit resolution, rail-to-rail
- Positive Reference Selection
- Unbuffered I/O pin output
- Internal connections to ADCs and
comparators
Voltage Reference:
- Fixed Voltage Reference with 1.024V, 2.048V
and 4.096V output levels
Clocking Structure
High-Precision Internal Oscillator:
- Selectable frequency range up to 32 MHz
x2/x4 PLL with Internal and External Sources
Low-Power Internal 32 kHz Oscillator
(LFINTOSC)
External 32 kHz Crystal Oscillator (SOCS)
External High-Speed Crystal Oscillators
2014-2016 Microchip Technology Inc. DS40001744C-page 3
PIC16(L)F183XX
TABLE 1: PIC16(L)F183XX Family Types
Device
Data Sheet Index
Program Memory (KB)
Program Memory (KW)
EEPROM (B)
RAM (B)
I/Os(1)
10-bit ADCs
Comparators
5-bit DAC
Timers 0/1/2
CCP/PWM
CWG
EUSART
SPI
I2C
CLC
NCO
PPS
ICD(2)
PIC16(L)F18313 (A) 3.5 2 256 256 6 5 1 1 1/1/1 2/2 1 1 1 1 2 1 Y I
PIC16(L)F18323 (A) 3.5 2 256 256 12 11 2 1 1/1/1 2/2 1 1 1 1 2 1 Y I
PIC16(L)F18324 (B) 7 4 256 512 12 11 2 1 1/3/3 4/2 2 1 1 1 4 1 Y I
PIC16(L)F18325 (C) 14 8 256 1K 12 11 2 1 1/3/3 4/2 2 1 2 2 4 1 Y I
PIC16(L)F18326 (D) 28 16 256 2K 12 11 2 1 1/3/3 4/2 2 1 2 2 4 1 Y I
PIC16(L)F18344 (B) 7 4 256 512 18 17 2 1 1/3/3 4/2 2 1 1 1 4 1 Y I
PIC16(L)F18345 (C) 14 8 256 1K 18 17 2 1 1/3/3 4/2 2 1 2 2 4 1 Y I
PIC16(L)F18346 (D) 28 16 256 2K 18 17 2 1 1/3/3 4/2 2 1 2 2 4 1 Y I
Note 1: One pin is input-only.
2: Debugging Methods: (I) – Integrated on Chip; E – using Emulation Header.
Data Sheet Index: (Unshaded devices are described in this document.)
A) DS40001799 PIC16(L)F18313/18323 Data Sheet, Full-Featured, Low Pin Count Microcontrollers with XLP
B) DS40001800 PIC16(L)F18324/18344 Data Sheet, Full-Featured, Low Pin Count Microcontrollers with XLP
C) DS40001795 PIC16(L)F18325/18345 Data Sheet, Full-Featured, Low Pin Count Microcontrollers with XLP
D) Future Release PIC16(L)F18326/18346 Data Sheet, Full-Featured, Low Pin Count Microcontrollers with XLP
Note: For other small form-factor package availability and marking information, please visit
http://www.microchip.com/packaging or contact your local sales office.
PIC16(L)F183XX
DS40001744C-page 4 2014-2016 Microchip Technology Inc.
TABLE 2: PACKAGES
Packages PDIP SOIC UDFN TSSOP UQFN SSOP
PIC16(L)F18313 X X X
PIC16(L)F18323 X X X X
PIC16(L)F18324 X X X X
PIC16(L)F18325 X X X X
PIC16(L)F18326 X X X X
PIC16(L)F18344 X X X X
PIC16(L)F18345 X X X X
PIC16(L)F18346 X X X X
Note: Pin details are subject to change.
H:|:H:J .I:I:I:I:I:I:J [[[E [[[EEEE
2014-2016 Microchip Technology Inc. DS40001744C-page 5
PIC16(L)F183XX
PIN DIAGRAMS
Pin Diagram – 8-Pin PDIP, SOIC, UDFN
Pin Diagram – 14-Pin PDIP, SOIC, TSSOP
Pin Diagram – 16-Pin UQFN (4x4)
1
2
3
4
VDD
RA5
RA4
VPP/MCLR/RA3
RA0/ICSPDAT
RA1/ICSPCLK
RA2
VSS
8
7
6
5
PIC16(L)F18313
Note: See Table 3 for location of all peripheral functions.
1
2
3
4
5
6
7
VDD
RA5
RA4
VPP/MCLR/RA3
RC5
RC4
RC3
RA0/ICSPDAT
RA1/ICSPCLK
RA2
RC0
RC1
RC2
14
13
12
11
10
9
8
VSS
PIC16(L)F18323
PIC16(L)F18324
PIC16(L)F18325
PIC16(L)F18326
Note: See Table 4, Table 5, Table 6 and Table 7 for location of all peripheral functions.
2
3
1
9
10
11
12
RC4
4
VSS
RA0/ICSPDAT
RA1/ICSPCLK
RA2
RC0
NC
NC
VDD
RA5
RA4
RA3/MCLR/VPP
RC5
RC3
RC2
RC1
6758
15 14
16 13
PIC16(L)F18323
PIC16(L)F18324
PIC16(L)F18325
PIC16(L)F18326
Note 1: See Table 4, Table 5, Table 6 and Table 7 for location of all peripheral functions.
2: It is recommended that the exposed bottom pad be connected to VSS.
DDDDDDDJJJ DDDDDDDEEE
PIC16(L)F183XX
DS40001744C-page 6 2014-2016 Microchip Technology Inc.
Pin Diagram – 20-Pin PDIP, SOIC, SSOP
Pin Diagram – 20-Pin UQFN (4x4)
PIC16(L)F18344
PIC16(L)F18345
PIC16(L)F18346
1
2
3
4
20
19
18
17
5
6
7
16
15
14
VDD
RA5
RA4
MCLR/VPP/RA3
RC5
RC4
RC3
VSS
RA0/ICSPDAT
RA1/ICSPCLK
RA2
RC0
RC1
RC2
8
9
10
13
12
11
RC6
RC7
RB7
RB4
RB5
RB6
Note: See Table 8, Table 9 and Table 10 for location of all peripheral functions.
-
89
2
3
1
14
15
16
10
11
6
12
13
17181920
7
5
4
PIC16(L)F18344
PIC16(L)F18345
PIC16(L)F18346
RA3/MCLR/VPP
RC5
RC4
RC3
RC6
RC7
RB7
RB4
RB5
RB6
RC1
RC0
RA2
RA1/ICSPCLK
RA0/ICSPDAT
Vss
VDD
RA4
RA5
RC2
Note 1: See Table 8, Table 9 and Table 10 for location of all peripheral functions.
2: It is recommended that the exposed bottom pad be connected to VSS.
2014-2016 Microchip Technology Inc. DS40001744C-page 7
PIC16(L)F183XX
PIN ALLOCATION TABLES
TABLE 3: 8-PIN ALLOCATION TABLE (PIC16(L)F18313)
I/O(2)
8-Pin PDIP/SOIC/UDFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 7ANA0 C1IN0+ DAC1OUT MDCIN1(1) — — — — — TX(1)
CK(1) CLCIN3(1) IOCA0 YICDDAT/
ICSPDAT
RA1 6ANA1 VREF+C1IN0- — DAC1REF+MDMIN
(1) ————SCK
(1)
SCL(1,3,4) RX(1)
DT(1,3) CLCIN2(1) IOCA1 YICDCLK/
ICSPCLK
RA2 5ANA2 VREF- — DAC1REF- T0CKI(1) CWG1(1) SDA(1,3,4)
SDO(1) INT(1)
IOCA2 Y —
RA3 4 — — — ————SS
(1) —CLCIN0
(1) IOCA3 YMCLR
VPP
RA4 3ANA4 C1IN1- T1G(1)
SOSCO — — — — IOCA4 YCLKOUT
OSC2
RA5 2ANA5 — MDCIN2(1) T1CKI(1)
SOSCIN
SOSCI
CCP1(1)
CCP2(1) ——CLCIN1(1) IOCA5 YCLKIN
OSC1
VDD 1 — — — — — — — VDD
VSS 8— — —————VSS
OUT(2)
C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A SDA(3) CK CLC1OUT CLKR — —
CCP2 PWM6 CWG1B SCL(3) DT(3) CLC2OUT —
— — CWG1C SDO TX — —
— — CWG1D SCK — —
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to the other pins (e.g., RA5) will operate, but logic levels will be standard TTL/
ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 8 2014-2016 Microchip Technology Inc.
TABLE 4: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18323)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 13 12 ANA0 C1IN0+ DAC1OUT — — — — IOCA0 YICDDAT/
ICSPDAT
RA1 12 11 ANA1 VREF+C1IN0-
C2IN0- —DAC1REF+ —— — ————IOCA1 YICDCLK/
ICSPCLK
RA2 11 10 ANA2 VREF- — DAC1REF- T0CKI(1) CWG1(1) — INT(1)
IOCA2 Y —
RA3 4 3 — — — —— — ————IOCA3 YMCLR
VPP
RA4 3 2 ANA4 — — T1G(1)
SOSCO IOCA4 YCLKOUT
OSC2
RA5 2 1 ANA5 —— — T1CKI(1)
SOSCIN
SOSCI
—— —
CLCIN3(1) IOCA5 YCLKIN
OSC1
RC0 10 9ANC0 C2IN0+ SCK(1)
SCL(1,3,4) IOCC0 Y —
RC1 9 8 ANC1 C1IN1-
C2IN1- —— —SDI
(1)
SDA(1,3,4) CLCIN2(1) IOCC1 Y —
RC2 8 7 ANC2 C1IN2-
C2IN2- MDCIN1(1) — — — — — IOCC2 Y —
RC3 7 6 ANC3 C1IN3-
C2IN3- ——MDMIN
(1) CCP2(1) ——SS
(1) CLCIN0(1) IOCC3 Y —
RC4 6 5 ANC4 TX(1)
CK(1) CLCIN1(1) IOCC4 Y —
RC5 5 4 ANC5 — MDCIN2(1) CCP1(1) ——RX
(1)
DT(1,3) ——IOCC5 Y —
VDD 116 — — — — — VDD
VSS 1413— — —— — ————VSS
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 9
PIC16(L)F183XX
OUT(2)
— — — C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A SDA(3) CK CLC1OUT CLKR — —
C2OUT CCP2 PWM6 CWG1B SCL(3) DT(3) CLC2OUT —
— — — CWG1C SDO TX — —
— — —— CWG1DSCK———
TABLE 4: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18323) (CONTINUED)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 10 2014-2016 Microchip Technology Inc.
TABLE 5: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18324)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 13 12 ANA0 C1IN0+ DAC1OUT — — — — IOCA0 YICDDAT/
ICSPDAT
RA1 12 11 ANA1 VREF+C1IN0-
C2IN0- —DAC1REF+ —— — ————IOCA1 YICDCLK/
ICSPCLK
RA2 11 10 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) — INT(1)
IOCA2 Y —
RA3 4 3 — — — —— — ————IOCA3 YMCLR
VPP
RA4 3 2 ANA4 — — T1G(1)
SOSCO IOCA4 YCLKOUT
OSC2
RA5 2 1 ANA5 —— — T1CKI(1)
SOSCIN
SOSCI
—— —
CLCIN3(1) IOCA5 YCLKIN
OSC1
RC0 10 9ANC0 C2IN0+ T5CKI(1) SCK(1)
SCL(1,3,4) IOCC0 Y —
RC1 9 8 ANC1 C1IN1-
C2IN1- — CCP4(1) ——SDI
(1)
SDA(1,3,4) CLCIN2(1) IOCC1 Y —
RC2 8 7 ANC2 C1IN2-
C2IN2- MDCIN1(1) — — — — — IOCC2 Y —
RC3 7 6 ANC3 C1IN3-
C2IN3- ——MDMIN
(1) T5G(1) CCP2(1) ——SS
(1) CLCIN0(1) IOCC3 Y —
RC4 6 5 ANC4 — — T3G(1) TX(1)
CK(1) CLCIN1(1) IOCC4 Y —
RC5 5 4 ANC5 — MDCIN2(1) T3CKI(1) CCP1(1) ——RX
(1)
DT(1,3) ——IOCC5 Y —
VDD 116 — — — — — VDD
VSS 1413— — —— — ————VSS
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 11
PIC16(L)F183XX
OUT(2)
— — — C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDA(3) CK CLC1OUT CLKR — —
— C2OUT CCP2 PWM6 CWG1B
CWG2B SCL(3) DT(3) CLC2OUT —
— — — CCP3 CWG1C
CWG2C SDO TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SCK — CLC4OUT —
TABLE 5: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18324) (CONTINUED)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 12 2014-2016 Microchip Technology Inc.
TABLE 6: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18325)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 13 12 ANA0 C1IN0+ DAC1OUT SS2(1) — — IOCA0 YICDDAT/
ICSPDAT
RA1 12 11 ANA1 VREF
+C1IN0-
C2IN0- —DAC1REF+— — — — — IOCA1 YICDCLK/
ICSPCLK
RA2 11 10 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) — INT(1)
IOCA2 Y —
RA3 4 3 — — —— — — IOCA3 YMCLR
VPP
RA4 3 2 ANA4 — — T1G(1)
SOSCO IOCA4 YCLKOUT
OSC2
RA5 2 1 ANA5 —— — T1CKI(1)
SOSCIN
SOSCI
—— —
CLCIN3(1) IOCA5 YCLKIN
OSC1
RC0 10 9ANC0 C2IN0+ T5CKI(1) SCK1(1)
SCL1(1,3,4) IOCC0 Y —
RC1 9 8 ANC1 C1IN1-
C2IN1- — CCP4(1) ——SDI1
(1)
SDA1(1,3,4) CLCIN2(1) IOCC1 Y —
RC2 8 7 ANC2 C1IN2-
C2IN2- MDCIN1(1) — — — — IOCC2 Y —
RC3 7 6 ANC3 C1IN3-
C2IN3- ——MDMIN
(1) T5G(1) CCP2(1) ——SS1
(1) CLCIN0(1) IOCC3 Y —
RC4 6 5 ANC4 — — T3G(1) SCK2(1)
SCL2(1,3,4) TX(1)
CK(1) CLCIN1(1) IOCC4 Y —
RC5 5 4 ANC5 — MDCIN2(1) T3CKI(1) CCP1(1) ——SDI2
(1)
SDA2(1,3,4) RX(1)
DT(1,3
)
——IOCC5 Y —
VDD 116 — — — — — VDD
VSS 14 13 — — — — — VSS
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 13
PIC16(L)F183XX
OUT(2)
C1OUT DDS DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDA1(3)
SDA2(3) CK CLC1OUT CLKR — —
— C2OUT CCP2 PWM6 CWG1B
CWG2B SCL1(3)
SCL2(3) DT(3) CLC2OUT —
— — — CCP3 CWG1C
CWG2C SDO1
SDO2 TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SCK1
SCK2 —CLC4OUT — —
TABLE 6: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18325) (CONTINUED)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 14 2014-2016 Microchip Technology Inc.
TABLE 7: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18326)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 13 12 ANA0 C1IN0+ DAC1OUT SS2(1) — — IOCA0 YICDDAT/
ICSPDAT
RA1 12 11 ANA1 VREF
+C1IN0-
C2IN0- —DAC1REF+— — — — — IOCA1 YICDCLK/
ICSPCLK
RA2 11 10 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) — INT(1)
IOCA2 Y —
RA3 4 3 — — —— — — IOCA3 YMCLR
VPP
RA4 3 2 ANA4 — — T1G(1)
SOSCO IOCA4 YCLKOUT
OSC2
RA5 2 1 ANA5 —— — T1CKI(1)
SOSCIN
SOSCI
—— —
CLCIN3(1) IOCA5 YCLKIN
OSC1
RC0 10 9ANC0 C2IN0+ T5CKI(1) SCK1(1)
SCL1(1,3,4) IOCC0 Y —
RC1 9 8 ANC1 C1IN1-
C2IN1- — CCP4(1) ——SDI1
(1)
SDA1(1,3,4) CLCIN2(1) IOCC1 Y —
RC2 8 7 ANC2 C1IN2-
C2IN2- MDCIN1(1) — — — — IOCC2 Y —
RC3 7 6 ANC3 C1IN3-
C2IN3- ——MDMIN
(1) T5G(1) CCP2(1) ——SS1
(1) CLCIN0(1) IOCC3 Y —
RC4 6 5 ANC4 — — T3G(1) SCK2(1)
SCL2(1,3,4) TX(1)
CK(1) CLCIN1(1) IOCC4 Y —
RC5 5 4 ANC5 — MDCIN2(1) T3CKI(1) CCP1(1) ——SDI2
(1)
SDA2(1,3,4) RX(1)
DT(1,3
)
——IOCC5 Y —
VDD 116 — — — — — VDD
VSS 14 13 — — — — — VSS
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 15
PIC16(L)F183XX
OUT(2)
C1OUT DDS DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDA1(3)
SDA2(3) CK CLC1OUT CLKR — —
— C2OUT CCP2 PWM6 CWG1B
CWG2B SCL1(3)
SCL2(3) DT(3) CLC2OUT —
— — — CCP3 CWG1C
CWG2C SDO1
SDO2 TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SCK1
SCK2 —CLC4OUT — —
TABLE 7: 14/16-PIN ALLOCATION TABLE (PIC16(L)F18326) (CONTINUED)
I/O(2)
14/16-Pin PDIP/SOIC/TSSOP
16-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g. RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 16 2014-2016 Microchip Technology Inc.
TABLE 8: 20-PIN ALLOCATION TABLE (PIC16(L)F18344)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 19 16 ANA0 C1IN0+ DAC1OUT — — — — IOCA0 YICDDAT/
ICSPDAT
RA1 18 15 ANA1 VREF
+C1IN0-
C2IN0- —DAC1REF+— —— ———IOCA1 YICDCLK/
ICSPCLK
RA2 17 14 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) CLCIN0(1) INT(1)
IOCA2 Y —
RA3 4 1 — — — —— ———IOCA3 YMCLR
VPP
RA4 320 ANA4 — — T1G(1)
T3G(1)
T5G(1)
SOSCO
CCP4(1) IOCA4 YCLKOUT
OSC2
RA5 219 ANA5 —— — T1CKI(1)
T3CKI(1)
T5CKI(1)
SOSCIN
SOSCI
—— —
IOCA5 YCLKIN
OSC1
RB4 13 10 ANB4 — — SDI(1)
SDA(1,3,4) CLCIN2(1) IOCB4 Y —
RB5 12 9ANB5 — RX
(1)
DT(1) CLCIN3(1) —IOCB5Y —
RB6 11 8ANB6 — — SCK(1)
SCL(1,3,4) IOCB6 Y —
RB7 10 7ANB7— — TX(1)
CK(1) ——IOCB7Y
RC0 16 13 ANC0 C2IN0+ — — — — — IOCC0 Y —
RC1 15 12 ANC1 C1IN1-
C2IN1- —— —IOCC1 Y —
RC2 14 11 ANC2 C1IN2-
C2IN2- MDCIN1(1) — — — — — IOCC2 Y —
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 17
PIC16(L)F183XX
RC3 7 4 ANC3 C1IN3-
C2IN3- ——MDMIN
(1) —CCP2
(1) — CLCIN1(1) IOCC3 Y
RC4 6 3 ANC4 — — — — IOCC4 Y —
RC5 5 2 ANC5 — MDCIN2(1) CCP1(1) —————IOCC5 Y —
RC6 8 5 ANC6 — — SS(1) IOCC6 Y
RC7 9 6 ANC7 — — — — — IOCC7 Y —
VDD 118 — — — — — VDD
VSS 20 17 — — — — — VSS
OUT(2)
— — — C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDO DT(3) CLC1OUT CLKR — —
— — — C2OUT CCP2 PWM6 CWG1B
CWG2B SCK CK CLC2OUT
— — — CCP3 CWG1C
CWG2C SCL(3) TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SDA(3) —CLC4OUT— — —
TABLE 8: 20-PIN ALLOCATION TABLE (PIC16(L)F18344) (CONTINUED)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 18 2014-2016 Microchip Technology Inc.
TABLE 9: 20-PIN ALLOCATION TABLE (PIC16(L)F18345)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 19 16 ANA0 C1IN0+ DAC1OUT — — — — IOCA0 YICDDAT/
ICSPDAT
RA1 18 15 ANA1 VREF
+C1IN0-
C2IN0- —DAC1REF+— SS2(1) ——IOCA1 YICDCLK/
ICSPCLK
RA2 17 14 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) CLCIN0(1) INT(1)
IOCA2 Y —
RA3 4 1 — —— — — IOCA3 YMCLR
VPP
RA4 320 ANA4 — — T1G(1)
T3G(1)
T5G(1)
SOSCO
CCP4(1) IOCA4 YCLKOUT
OSC2
RA5 219 ANA5 —— — T1CKI(1)
T3CKI(1)
T5CKI(1)
SOSCIN
SOSCI
—— —
IOCA5 YCLKIN
OSC1
RB4 13 10 ANB4 — — SDI1(1)
SDA1(1,3,4) CLCIN2(1) IOCB4 Y —
RB5 12 9ANB5— — SDI2
(1)
SDA2(1,3,4) RX(1)
DT(1) CLCIN3(1) IOCB5 Y
RB6 11 8ANB6 — — SCK1(1)
SCL1(1,3,4) IOCB6 Y —
RB7 10 7ANB7— — SCK2
(1)
SCL2(1,3,4) TX(1)
CK(1) IOCB7 Y
RC0 16 13 ANC0 C2IN0+ — — — — — IOCC0 Y —
RC1 15 12 ANC1 C1IN1-
C2IN1- —— —IOCC1 Y —
RC2 14 11 ANC2 C1IN2-
C2IN2- — MDCIN1(1) —— — ———
IOCC2 Y
RC3 7 4 ANC3 — C1IN3-
C2IN3- ——MDMIN
(1) — CCP2(1) — CLCIN1(1) IOCC3 Y
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 19
PIC16(L)F183XX
RC4 6 3 ANC4 — — — — IOCC4 Y —
RC5 5 2 ANC5 — MDCIN2(1) CCP1(1) —————IOCC5 Y —
RC6 8 5 ANC6 — — SS(1) IOCC6 Y
RC7 9 6 ANC7 — — — — IOCC7 Y —
VDD 118 — — — — VDD
VSS 20 17 — — — — — VSS
OUT(2)
C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDO1
SDO2 DT(3) CLC1OUT CLKR — —
— C2OUT CCP2 PWM6 CWG1B
CWG2B SCK1
SCK2 CK CLC2OUT
— — — CCP3 CWG1C
CWG2C SCL1(3)
SCL2(3) TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SDA1(3)
SDA2(3) —CLC4OUT— — —
TABLE 9: 20-PIN ALLOCATION TABLE (PIC16(L)F18345) (CONTINUED)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
PIC16(L)F183XX
DS40001744C-page 20 2014-2016 Microchip Technology Inc.
TABLE 10: 20-PIN ALLOCATION TABLE (PIC16(L)F18346)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
RA0 19 16 ANA0 C1IN0+ DAC1OUT — — — — IOCA0 YICDDAT/
ICSPDAT
RA1 18 15 ANA1 VREF
+C1IN0-
C2IN0- —DAC1REF+— SS2(1) ——IOCA1 YICDCLK/
ICSPCLK
RA2 17 14 ANA2 VREF- — DAC1REF- T0CKI(1) CCP3(1) CWG1(1)
CWG2(1) CLCIN0(1) INT(1)
IOCA2 Y —
RA3 4 1 — —— — — IOCA3 YMCLR
VPP
RA4 320 ANA4 — — T1G(1)
T3G(1)
T5G(1)
SOSCO
CCP4(1) IOCA4 YCLKOUT
OSC2
RA5 219 ANA5 —— — T1CKI(1)
T3CKI(1)
T5CKI(1)
SOSCIN
SOSCI
—— —
IOCA5 YCLKIN
OSC1
RB4 13 10 ANB4 — — SDI1(1)
SDA1(1,3,4) CLCIN2(1) IOCB4 Y —
RB5 12 9ANB5— — SDI2
(1)
SDA2(1,3,4) RX(1)
DT(1) CLCIN3(1) IOCB5 Y
RB6 11 8ANB6 — — SCK1(1)
SCL1(1,3,4) IOCB6 Y —
RB7 10 7ANB7— — SCK2
(1)
SCL2(1,3,4) TX(1)
CK(1) IOCB7 Y
RC0 16 13 ANC0 C2IN0+ — — — — — IOCC0 Y —
RC1 15 12 ANC1 C1IN1-
C2IN1- —— —IOCC1 Y —
RC2 14 11 ANC2 C1IN2-
C2IN2- — MDCIN1(1) —— — ———
IOCC2 Y
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
2014-2016 Microchip Technology Inc. DS40001744C-page 21
PIC16(L)F183XX
RC3 7 4 ANC3 — C1IN3-
C2IN3- ——MDMIN
(1) — CCP2(1) — CLCIN1(1) IOCC3 Y
RC4 6 3 ANC4 — — — — IOCC4 Y —
RC5 5 2 ANC5 — MDCIN2(1) CCP1(1) —————IOCC5 Y —
RC6 8 5 ANC6 — — SS(1) IOCC6 Y
RC7 9 6 ANC7 — — — — IOCC7 Y —
VDD 118 — — — — VDD
VSS 20 17 — — — — — VSS
OUT(2)
C1OUT NCO DSM TMR0 CCP1 PWM5 CWG1A
CWG2A SDO1
SDO2 DT(3) CLC1OUT CLKR — —
— C2OUT CCP2 PWM6 CWG1B
CWG2B SCK1
SCK2 CK CLC2OUT
— — — CCP3 CWG1C
CWG2C SCL1(3)
SCL2(3) TX CLC3OUT — —
— — — CCP4 CWG1D
CWG2D SDA1(3)
SDA2(3) —CLC4OUT— — —
TABLE 10: 20-PIN ALLOCATION TABLE (PIC16(L)F18346) (CONTINUED)
I/O(2)
20-Pin PDIP/SOIC/SSOP
20-Pin UQFN
ADC
Reference
Comparator
NCO
DAC
DSM
Timers
CCP
PWM
CWG
MSSP
EUSART
CLC
CLKR
Interrupt
Pull-up
Basic
Note 1: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers.
2: All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: These pins are configured for I2C logic levels; clock and data signals may be assigned to any of these pins. Assignments to other pins (e.g., RA5) will operate, but logic levels will be standard
TTL/ST as selected by the INLVL register.
YSTEM
DS40001744C-page 22 2014-2016 Microchip Technology Inc.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O,
Total Endurance, TSHARC, USBCheck, VariSense,
ViewSpan, WiperLock, Wireless DNA, and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2014-2016, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
ISBN: 978-1-5224-0183-4
Note the following details of the code protection feature on Microchip devices:
Microchip products meet the specification contained in their particular Microchip Data Sheet.
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
QUALITY MANAGEMENT S
YSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
6‘ ‘MICRDCHIP
2014-2016 Microchip Technology Inc. DS40001744C-page 23
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Dongguan
Tel: 86-769-8702-9880
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
ASIA/PACIFIC
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-3019-1500
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Dusseldorf
Tel: 49-2129-3766400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Venice
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Poland - Warsaw
Tel: 48-22-3325737
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Worldwide Sales and Service
07/14/15