1462000001 Prod Spec Datasheet by Molex

View All Related Products | Download PDF Datasheet
D molex“ C TITLE TABLE OF CONTENTS REV‘SION. ECR/ECN INFORMATION. EC No. DATE. T‘TLE. SHEET No. DOCUMENT NUMBER. CREATED / REV‘SED BY. CHECKED BY. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
Full LTE SMT Antenna
SHEET No.
A
EC No:
103559
1 of 5
DATE:
2016/02/22
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001
Benson Liu 2016-02-22
Chris Zhong 2016-02-22
Welson Tan2016-02-22
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
d
TITLE
Full LTE SMT Antenna
TABLE OF CONTENTS
1.0 SCOPE
2.0 PRODUCT DESCRIPTION
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
4.0 RATINGS
5.0 PERFORMANCE
6.0 TEST GROUPINGS
7.0 RECOMMENDED REFLOW CONDITION
8.0 PACKING
D molex“ C Full LTE SMT Antenna REVTSION. ECR/ECN INFORMATION. EC No. DATE. TTTLE. SHEET No. DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED BY. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
Full LTE SMT Antenna
SHEET No.
A
EC No:
103559
2 of 5
DATE:
2016/02/22
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001
Benson Liu 2016-02-22
Chris Zhong 2016-02-22
Welson Tan2016-02-22
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
d
Full LTE SMT Antenna
1.0 SCOPE
This Product Specification covers the mechanical, electrical and environmental performances
requirements and test methods for Full LTE SMT antenna.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER
Product name: Full LTE SMT Antenna 146200-0001
2.2 Design and Construction
Antenna shall be of the design, construction and physical dimensions specified on the
applicable sales drawing.
2.3 Materials
a) Ceramic: Refer to respective Molex sales or engineering drawings
b) Plating: Refer to respective Molex sales or engineering drawings
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
See drawings and other sections of this specification for the relevant reference documents. In
cases where the specification differs from the drawings, the drawings take precedence.
4.0 RATINGS
4.1 RF POWER
2 WATTS
4.2 TEMPERATURE
Operating: - 30°C to + 85°C
Storage : - 40°C to + 95°C
4.3 HUMIDITY
Operating :-30°C to+85°C
-30°C to+50°C, 85%RH or less
+50°C to+85°C, 60%RH or less
Storage : -40°C to+95°C
-40°C to+50°C, 85%RH or less
+50°C to+95°C, 60%RH or less
D molex’ C REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. EC No. DATE. DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED BY. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
Full LTE SMT Antenna
SHEET No.
A
EC No:
103559
3 of 5
DATE:
2016/02/22
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001
Benson Liu 2016-02-22
Chris Zhong 2016-02-22
Welson Tan2016-02-22
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
d
5.0 PERFORMANCE
5.2 MECHANICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
5.2.1
Ag thickness measure
Use X-ray measure the thickness of Ag
Ag thickness spec: 8-10um.
5.2.2
Cross cut Test
Cross cut adhesion test
Testing is performed in accordance with
ASTM D-3359-93
Acceptance criteria > 2B as
acceptance, <35% peeling off.
5.3 RELIABILITY REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
5.3.1
Peeling Force
Apply six axial peeling force on parts
soldered on the PCB at the speed rate of
253 mm/minute
8 N Min
5.1 ELECTRICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
5.1.1
Frequency Range
Measure antenna on
recommended PCB through VNA
E5071C
698-960MHz
1.7-2.7GHz
5.1.2
Return Loss
Measure antenna on
recommended PCB through VNA
E5071C
< -5 dB
< -5 dB
5.1.3
Peak Gain
Measure antenna on
recommended PCB through OTA
chamber
1.1dBi
4.5dBi
5.1.4
Avg. Total
Efficiency
Measure antenna on
recommended PCB through OTA
chamber
60%
70%
5.1.5
Polarization
Measure antenna on
recommended PCB through OTA
chamber
Linear
Linear
5.1.6
Input Impedance
Measure antenna on
recommended PCB through VNA
E5071C
50 Ohms
50 Ohms
D 55 REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. EC No. DATE. DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED BY. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
Full LTE SMT Antenna
SHEET No.
A
EC No:
103559
4 of 5
DATE:
2016/02/22
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001
Benson Liu 2016-02-22
Chris Zhong 2016-02-22
Welson Tan2016-02-22
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
d
The meaning of text “No mechanical damage” in the table above is:
a. no soldering problem
b. no adhesion problem of glue
c. no peel off of plating
5.4 ENVIRONMENTAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
5.4.1
Humidity Test
1.Test condition:
The device under test is kept for 12 hours
in an environment with a temperature of 55
degrees and a relating humidity of 95%.
Thereafter for 12 Hours in an environment
with a temperature of 25 degrees and a
relative humidity of 95%. The cycle is
repeated until a total of 6 cycles have
been completed. Hereafter the conditions
are stabilized at room temperature.
1) Parts should meet RF spec
before and after test.
2 No cosmetic problem
5.4.2
Temperature
cycling test
1.Test condition:
The device under test at -40 125
by 72 cycles, Dwell of 30 min, transition
time between Dwell 15 sec (~ 61 min /
cycle ) and each item should be measured
after exposing them in normal temperature
and humidity for 24 h.
1) Parts should meet RF spec
before and after test.
2 No cosmetic problem
5.4.3
High Temperature
Test condition:
1) Temperature:125,
time:1008hours
2) There is no substantial
obstruction to air flow across and
around the samples, and the
samples are not touching each
other
1) Parts should meet RF
spec before and after
test.
2) No cosmetic problem
5.4.4
Salt mist test
1.Test condition:
The device under test is exposed to a
spray of a 5% (by volume) resolution of
Nacl in water for 2 hours. Thereafter the
device under test is left for 1 week in room
temperature at a relative humidity of 95%.
The cycle is repeated until a total of 2
cycles have been completed. Here after
the conditions are stabilized at room
temperature.
1) Parts should meet RF spec
before and after test.
2) No visible corrosion.
Discoloration accept.
D molex“ C temper-mm! C) 2w um 150 no I20 I00 I ‘ 30:“an Ion“ “we. 20.“. , I |?mm max} 101090“ man I I I I I BOm‘JDsL‘cryp-(Al‘ I I I I I I I v rIgI \q/hno mo mm mun .— Pr.“ mmvamrc 7:0 lo 235 c I I 10 I , I I 90 I l n -—v— ‘ 0 no so 90 I20 150 I50 210 240 279 Ylmc (Second-l III In; W Iona macaw snow noI nxeoou 2 5cm :0 prawn? swabs” locmabon 0! may dnbfii REVISION: ECR/ECN INFORMATION: TITLE: SHEET N0. EC No: DATE: DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
Full LTE SMT Antenna
SHEET No.
A
EC No:
103559
5 of 5
DATE:
2016/02/22
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001
Benson Liu 2016-02-22
Chris Zhong 2016-02-22
Welson Tan2016-02-22
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
d
6.0 TEST GROUPINGS
Note: All test specimens (except group 5) shall pass the reflow process for 3 times.
Test
Item
Description
Group1
Group2
Group3
Group4
Group5
Group6
Group7
5.2.1
Ag thickness
X
5.2.2
Cross cut
X
5.3.1
Peeling Force
X
5.4.1
Humidity Test
X
5.4.2
Temperature
cycling test
X
5.4.3
High Temperature
X
5.4.4
Salt mist test
X
Sample Quantity
5
5
5
5
5
5
5
7.0 RECOMMENDED REFLOW CONDITION
8.0 PACKAGING
Refer to the Molex related packaging drawings.

Products related to this Datasheet

RF ANT 829MHZ/2.2GHZ CHIP SLD
RF ANT 829MHZ/2.2GHZ CHIP SLD
RF ANT 829MHZ/2.2GHZ CHIP SLD