XLamp® XM-L2 LEDs Datasheet by Cree Inc.

View All Related Products | Download PDF Datasheet
Product family data sheet
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and
XLamp® are registered trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
WWW.CREE.COM/XLAMP
CLD-DS61 REV 6K
Cree® XLamp® XM-L2 LEDs
PRODUCT DESCRIPTION
The XLamp® XM-L2 LED builds on the
unprecedented performance of the
original XM-L, increasing lumen output
up to 20% while providing a single die
LED point source for precise optical
control. The XM-L2 LED shares the same
mechanical and optical footprint as the
original XM-L, providing a seamless
upgrade path and shortened design
cycle.
XLamp XM-L2 LEDs are the ideal choice
for lighting applications where high
light output and maximum efficacy are
required, such as LED light bulbs, outdoor
lighting, portable lighting, indoor lighting
and solar-powered lighting.
FEATURES
Available in white, 70-CRI white,
80-CRI white, 85-CRI white and
90-CRI white
ANSI-compatible chromaticity bins
Binned at 85°C
Maximum drive current: 3000mA
Low thermal resistance: 2.5°C/W
Wide viewing angle: 125°
Unlimited floor life at
≤ 30ºC/85% RH
Reflow solderable - JEDEC
J-STD-020C
Electrically neutral thermal path
RoHS and REACh compliant
UL® recognized component
(E349212)
TABLE OF CONTENTS
Characteristics ........................................2
Flux Characteristics ................................3
Relative Spectral Power Distribution .....5
Relative Flux vs. Junction Temperature .5
Electrical Characteristics ........................ 6
Relative Flux vs. Current .........................6
Relative Chromaticity vs. Current ...........7
Relative Chromaticity vs. Temperature .. 7
Typical Spatial Distribution .....................8
Thermal Design .......................................8
Reflow Soldering Characteristics ........... 9
Notes .....................................................10
Mechanical Dimensions .......................12
Tape and Reel ........................................ 13
Packaging ..............................................14
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
2
XLamp® Xm-L2 LED
CHARACTERISTICS
Characteristics Unit Minimum Typical Maximum
Thermal resistance, junction to solder point °C/W 2.5
Viewing angle (FWHM) degrees 125
Temperature coefficient of voltage mV/°C -1.6
ESD withstand voltage (HBM per Mil-Std-883D) V 8000
DC forward current mA 3000
Reverse voltage V -5
Forward voltage (@ 700mA, 85°C) V 2.85 3.15
Forward voltage (@ 1500mA, 85°C) V 3.05
Forward voltage (@ 3000mA, 85°C) V 3.3
LED junction temperature °C 150
.EEE-
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
3
XLamp® Xm-L2 LED
Notes:
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 10).
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65. Minimum CRI for 70-CRI White is 70.
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75. Minimum CRI for 80-CRI White is 80.
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80. Minimum CRI for 85-CRI White is 85.
Minimum CRI for 90-CRI White is 90.
* Flux values @ 25°C are calculated and are for reference only.
** Calculated flux values at 1000mA, 1500mA and 2000mA are for reference only.
FLUX CHARACTERISTICS (TJ
The following table provides several base order codes for XLamp XM-L2 LEDs. It is important to note that the base order codes listed
here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the
order-code nomenclature, please consult the XLamp XM LED Family Binning and Labeling document.
Color
CCT Range 

Calculated Minimum Luminous Flux
 Order Code
Min. Max. Group 


 1000 mA 1500 mA 2000 mA
Cool White 5000 K 8300 K
T5 260 296 357 502 631 XMLBWT-00-0000-0000T5051
T6 280 318 385 541 679 XMLBWT-00-0000-0000T6051
U2 300 342 412 580 728 XMLBWT-00-0000-0000U2051
U3 320 364 439 618 776 XMLBWT-00-0000-0000U3051
Neutral White 3700 K 5000 K
T4 240 273 330 464 582 XMLBWT-00-0000-000LT40E4
T5 260 296 357 502 631 XMLBWT-00-0000-000LT50E4
T6 280 318 385 541 679 XMLBWT-00-0000-000LT60E4
U2 300 342 412 580 728 XMLBWT-00-0000-000LU20E4
Warm White 2600 K 3700 K
T2 200 227 275 386 485 XMLBWT-00-0000-000LT20E7
T3 220 250 302 425 534 XMLBWT-00-0000-000LT30E7
T4 240 273 330 464 582 XMLBWT-00-0000-000LT40E7
T5 260 296 357 502 631 XMLBWT-00-0000-000LT50E7
70-CRI White 3700 K 5000 K
T5 260 296 357 502 631 XMLBWT-00-0000-000BT50E3
T6 280 318 385 541 679 XMLBWT-00-0000-000BT60E3
U2 300 342 412 580 728 XMLBWT-00-0000-000BU20E3
U3 320 364 439 618 776 XMLBWT-00-0000-000BU30E3
80-CRI White 2600 K 4300 K
T2 200 227 275 386 485 XMLBWT-00-0000-000HT20E7
T3 220 250 302 425 534 XMLBWT-00-0000-000HT30E7
T4 240 273 330 464 582 XMLBWT-00-0000-000HT40E7
T5 260 296 357 502 631 XMLBWT-00-0000-000HT50E7
85-CRI White 2600 K 3200 K
S4 164 186 225 317 398 XMLBWT-00-0000-000PS40E7
S5 172 196 236 332 417 XMLBWT-00-0000-000PS50E7
S6 182 207 250 352 442 XMLBWT-00-0000-000PS60E7
T2 200 227 275 386 485 XMLBWT-00-0000-000PT20E7
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
4
XLamp® Xm-L2 LED
Notes:
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 10).
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65. Minimum CRI for 70-CRI White is 70.
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75. Minimum CRI for 80-CRI White is 80.
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80. Minimum CRI for 85-CRI White is 85.
Minimum CRI for 90-CRI White is 90.
* Flux values @ 25°C are calculated and are for reference only.
** Calculated flux values at 1000mA, 1500mA and 2000mA are for reference only.
Color
CCT Range 

Calculated Minimum Luminous Flux
 Order Code
Min. Max. Group 


 1000 mA 1500 mA 2000 mA
90-CRI White 2600 K 3200 K
S4 164 186 225 317 398 XMLBWT-00-0000-000US40E7
S5 172 196 236 332 417 XMLBWT-00-0000-000US50E7
S6 182 207 250 352 442 XMLBWT-00-0000-000US60E7
T2 200 227 275 386 485 XMLBWT-00-0000-000UT20E7
FLUX CHARACTERISTICS (TJ
_5000 K- 8300 K CDT —3700 K- 5000 K CDT —2600 K- 3700 K COT
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
5
XLamp® Xm-L2 LED
RELATIVE SPECTRAL POWER DISTRIBUTION
RELATIVE FLUX VS. JUNCTION TEMPERATURE (IFm
Relative Spectral Power
0
20
40
60
80
100
380 430 480 530 580 630 680 730 780
Relative Radiant Power (%)
Wavelength (nm)
5000 K - 8300 K CCT
3700 K - 5000 K CCT
2600 K - 3700 K CCT
Relative Flux Output vs. Junction Temperature
0
20
40
60
80
100
120
25 50 75 100 125 150
Relative Luminous Flux (%)
Junction Temperature (ºC)
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
6
XLamp® Xm-L2 LED
ELECTRICAL CHARACTERISTICS (TJ
RELATIVE FLUX VS. CURRENT (TJ
Electrical Characteristics (Tj = 85°C)
0
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
2.6 2.8 3.0 3.2 3.4
Forward Current (mA)
Forward Voltage (V)
Relative Intensity vs. Current (Tj = 85°C)
0
50
100
150
200
250
300
350
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Relative Luminous Flux (%)
Forward Current (mA)
_ ACCx _ _ ACCy Accx _ _ ACCy
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
7
XLamp® Xm-L2 LED


Relative Chromaticity Vs. Current, WW
-0.012
-0.008
-0.004
0.000
0.004
0.008
0.012
0 500 1000 1500 2000 2500 3000
Current (mA)
ΔCCx
ΔCCy
Tsp (°C)
ΔCCx
ΔCCy
—Rj-a = 4“C/W —Rj-a = 7“C/W —Rj-a =15'C/W
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
8
XLamp® Xm-L2 LED
TYPICAL SPATIAL DISTRIBUTION
THERMAL DESIGN
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end
product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
Typical Spatial Radiation Pattern
0
20
40
60
80
100
-90 -70 -50 -30 -10 10 30 50 70 90
Relative Luminous Intensity (%)
Angle (º)
Thermal Design
Cool White
0
500
1000
1500
2000
2500
3000
3500
0 20 40 60 80 100 120 140 160
Maximum Current (mA)
Ambient Temperature (ºC)
Rj-a = 4°C/W
Rj-a = 7°C/W
Rj-a = 10°C/W
Rj-a = 15°C/W
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
9
XLamp® Xm-L2 LED
REFLOW SOLDERING CHARACTERISTICS
In testing, Cree has found XLamp XM-L2 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general
guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used,
and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature Lead-Free Solder
Average Ramp-Up Rate (Tsmax to Tp) 1.2°C/second
Preheat: Temperature Min (Tsmin) 120 °C
Preheat: Temperature Max (Tsmax)170 °C
Preheat: Time (tsmin to tsmax) 65-150 seconds
Time Maintained Above: Temperature (TL)217 °C
Time Maintained Above: Time (tL) 45-90 seconds
Peak/Classification Temperature (Tp) 235 - 245 °C
Time Within 5°C of Actual Peak Temperature (tp) 20-40 seconds
Ramp-Down Rate 1 - 6 °C/second
Time 25°C to Peak Temperature 4 minutes max.
Note: All temperatures refer to the topside of the package, measured on the package body surface.
IPC/JEDEC J-STD-020C
TP
TL
Temperature
Time
t 25˚C to Peak
Preheat
ts
tS
tP
25
Ramp-down
Ramp-up
Critical Zone
TL to TP
Tsmax
Tsmin
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
10
XLamp® Xm-L2 LED
NOTES
Measurements
The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only
and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number
of factors that are not within Crees control and are not intended or provided as operational specifications for the products. Calculated
values are provided for informational purposes only and are not intended or provided as specifications.
fi
Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp
LEDs and details of Crees pre-release qualification testing for XLamp LEDs.
Lumen Maintenance
Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance.
For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Crees lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LED junction temperature.
Moisture Sensitivity
Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp XM-L2 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in
conditions of 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs
in the original MBP.
RoHS Compliance
The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as
implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product
Ecology section of the Cree website.
REACh Compliance
REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA)
has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to
insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available
upon request.
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
11
XLamp® Xm-L2 LED
UL® Recognized Component
This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED
package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750.
Vision Advisory
WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please
refer to the LED Eye Safety application note.
NOTES - CONTINUED
I T 4L? M 7 EH? szu MW! ,WT fir
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
12
XLamp® Xm-L2 LED
MECHANICAL DIMENSIONS
Thermal vias, if present, are not shown on these drawings.
All measurements are ±.13 mm unless otherwise indicated.
Top View Bottom View
Side View
Recommended PCB Solder Pad Recommended Stencil Pattern

SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
5.00
5.00
R2.26
3.02
0.73
.50
3.78
2.78
4.78
4.78
.50
4.78
.80
.50
.25
.80
.25
.97
4.78
.50
.50
2.78
4.78
4.78
1/116.000
B
2610-00032
OUTLINE DRAWING, 5050 XMLB
--
--
----
----
11/14/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
5.00
5.00
R2.26
3.02
0.73
.50
3.78
2.78
4.78
4.78
.50
4.78
.80
.50
.25
.80
.25
.97
4.78
.50
.50
2.78
4.78
4.78
1/116.000
B
2610-00032
OUTLINE DRAWING, 5050 XMLB
--
--
----
----
11/14/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
”1K ‘ ‘ ooéd 0000000 VVV‘ EIIEEE EEEEEEEJ
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
13
XLamp® Xm-L2 LED
TAPE AND REEL
All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.
Except as noted, all dimensions in mm.
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTANED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
SURFACE FINISH:
63
330
+.25
-.75
12.4
+1.0
-.5
MEASURED AT EDGE
16.4
+0.2
.0
MEASURED AT HUB
12.4
+.2
.0
MEASURED AT HUB
±.213.1
1.9±.4
±.421
60° 60°
1/10.500
A
2400-00009
REEL, 13" X 12MM, 3 PIECE SNAP
-
ANTI-STATIC HIPS
----
----
09/29/09D. CRONIN
2400-00009
INDEX QTY ITEM COMMENTS
1 1 2400-00009-CORE
2 2 2400-00009-REEL
REVISONS
REV DESCRIPTION BY DATE APP'D
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
Trailer
160mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
Loaded Pockets
(1000 Lamps)
Leader
400mm (min.) of
empty pockets with
at least 100mm
sealed by tape
(40 empty pockets min.)
12
1.75
4
83.35
1/13.000
B
2402-00012
XM LOADING SPEC
--
--
----
----
06/08/10D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
A Loaded pocket count was 750 DDS 11/8/10 BS
B MADE CATHODE AND ANODE NOTE LARGER DC 2/26/12
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
1
234
6 5
D
C
B
A
APP'DDATEBY
REVISIONS
REV DESCRIPTION
SIZE
TITLE
OF
REV.
SHEET
A
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
1
23456
4600 Silicon Drive
Fax (919) 313-5558
Durham, N.C 27703
Phone (919) 313-5300
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
63
1/1DRAWING SCALE
A
2402-00011
XM 5050 CARRIER TAPE
4/23/10 D. CRONIN
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
.36[.014]
T
5.40[.213]
Ao
3.35[.132]
Ko
3.0°
5.40[.213]
Bo
2.00[.079]
P2
4.00[.157]
Po
Do1.50 +.10
-.00 .0591 +.0039
-.0000 [ ]
10.25
[.404]
E2
7.0°
12.00[.472]
NOMINAL
12.30 [.484]
MAX
W
1.75[.069]
E1
5.50[.217]F
1.50[.059]
D1
8.00[.315]
P
POCKET SIZE
Ao - 5.40mm [.213"]
Bo - 5.40mm [.213"]
Ko - 3.35mm [.132"]
1
234
6 5
D
C
B
A
APP'DDATEBY
REVISIONS
REV DESCRIPTION
SIZE
TITLE
OF
REV.
SHEET
A
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
1
23456
4600 Silicon Drive
Fax (919) 313-5558
Durham, N.C 27703
Phone (919) 313-5300
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
63
1/1DRAWING SCALE
A
2402-00011
XM 5050 CARRIER TAPE
4/23/10 D. CRONIN
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
.36[.014]
T
5.40[.213]
Ao
3.35[.132]
Ko
3.0°
5.40[.213]
Bo
2.00[.079]
P2
4.00[.157]
Po
Do1.50 +.10
-.00 .0591 +.0039
-.0000 [ ]
10.25
[.404]
E2
7.0°
12.00[.472]
NOMINAL
12.30 [.484]
MAX
W
1.75[.069]
E1
5.50[.217]F
1.50[.059]
D1
8.00[.315]
P
POCKET SIZE
Ao - 5.40mm [.213"]
Bo - 5.40mm [.213"]
Ko - 3.35mm [.132"]
1
234
6 5
D
C
B
A
APP'DDATEBY
REVISIONS
REV DESCRIPTION
SIZE
TITLE
OF
REV.
SHEET
A
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
1
23456
4600 Silicon Drive
Fax (919) 313-5558
Durham, N.C 27703
Phone (919) 313-5300
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
63
1/1DRAWING SCALE
A
2402-00011
XM 5050 CARRIER TAPE
4/23/10 D. CRONIN
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
.36[.014]
T
5.40[.213]
Ao
3.35[.132]
Ko
3.0°
5.40[.213]
Bo
2.00[.079]
P2
4.00[.157]
Po
Do1.50 +.10
-.00 .0591 +.0039
-.0000 [ ]
10.25
[.404]
E2
7.0°
12.00[.472]
NOMINAL
12.30 [.484]
MAX
W
1.75[.069]
E1
5.50[.217]F
1.50[.059]
D1
8.00[.315]
P
POCKET SIZE
Ao - 5.40mm [.213"]
Bo - 5.40mm [.213"]
Ko - 3.35mm [.132"]
Copyright © 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. UL® and
the UR logo are registered trademarks of UL LLC.
14
XLamp® Xm-L2 LED
PACKAGING
Label with Cree Bin
Code, Qty, Lot # Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Dessicant
(inside bag)
Humidity Indicator
Card (inside bag)
Patent Label
Label with Customer Order
Code, Qty, Reel ID, PO #
Patent Label
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel

Products related to this Datasheet

LED XLAMP NEUTRAL WHT 4500K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP COOL WHITE 5700K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP XM-L2 WHITE SMD
LED XLAMP COOL WHITE 5700K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP COOL WHITE 6500K 2SMD
LED XLAMP XM-L2 WHITE SMD
LED XLAMP COOL WHITE 5000K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP COOL WHITE 6500K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP COOL WHITE 5000K 2SMD
LED XLAMP COOL WHITE 6500K 2SMD
LED XLAMP WARM WHITE 3000K 2SMD
LED XLAMP COOL WHITE 6200K 2SMD
LED XLAMP COOL WHITE 5700K 2SMD
LED XLAMP XM-L2 WHITE SMD
LED XLAMP NEUTRAL WHT 4500K 2SMD
LED XLAMP XM-L2 WHITE SMD
LED XLAMP NEUTRAL WHT 4000K 2SMD
LED XLAMP WARM WHITE 2700K 2SMD
LED XLAMP WARM WHITE 3500K 2SMD
LED XLAMP COOL WHITE 5700K 2SMD
LED XLAMP NEUTRAL WHT 4500K 2SMD
LED XLAMP NEUTRAL WHT 4500K 2SMD
LED XLAMP WARM WHITE 3000K 2SMD
LED XLAMP COOL WHITE 6000K 2SMD
LED XLAMP COOL WHITE 5000K 2SMD