®®®®®
Swanstrom
18
STUSA Electronic Tools
STUSA Electronic Tools
MX54 Oval head semi-flush diagonal cutters
• Strongest tips and beveled edge for long life
• Induction hardened edges optimize cutting ease and life
• OAL 4.25” Jaw 0.60”
MX54-9 Oval head diagonal flush cutters
• Strong tips and long life
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
MX54-3 Oval relieved/slim diagonal flush cutters
• For intricate and repetitive work between and under closely
spaced components
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
MX54-5 Taper head diagonal flush cutters
• For intricate work between closely spaced components
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
EMX54-3 Oval relieved/slim diagonal flush cutters
with ergonomic handles
• For intricate and repetitive work between and under closely
spaced components
• Induction hardened edges optimize cutting ease and life
• E denotes ergonomic (double curve) handles to spread pressure
across the palm and relieve carpal tunnel
pocket pressure
• Most comfortable hand, wrist and arm positions
• Flush cut for a sharper edge requiring minimum squeeze
and reduces spike
• OAL 5.60” Jaw 0.60”
EAX54 Angle end flush cutters with ergonomic handles
• Angled 60º/30º for ergonomic work positions
• Induction hardened edges optimize cutting ease and life
• E denotes ergonomic (double curve) handles to spread pressure
across the palm and relieve carpal tunnel
pocket pressure
• For most comfortable hand, wrist and arm positions
• Flush cut for sharper edge, minimum squeeze, maximum ease
• OAL 5.70” Jaw 0.63”
• Engineered for small hands and intricate work
• Forged steel for strength, durability, and long life
• Machined with precision for tight tolerances
• Hardened electronically, tempered for toughness
• Honed to precise cut requirements
• Stainless steel leaf springs welded in place
• Cushioned grips for operator comfort
• ESD SAFE for component protection
13190 catalog pgs 6/30/08 9:23 AM Page 18
<><>STUSA Electronic Tools
AX54 Angle end flush cutters
• Angled 60º/30º for most ergonomic work positions
• Induction hardened edges optimize cutting ease and life
• Flush cut -for a sharp edge requiring less squeeze and reduces
spike
• OAL 4.75” Jaw 0.63”
LX4 Submini needle nose serrated pliers
• Where short handles are a must
• Each jaw has fine parallel serrations and beveled edges
• OAL 4.50” Jaw 0.92”
LX4G Submini needle nose smooth pliers
• Where short handles are a must
• Each jaw is smooth with beveled edges
• OAL 4.50” Jaw 0.92”
LX54 Thin long nose serrated pliers
• Each jaw has fine parallel serrations and beveled edges
• OAL 5.25” Jaw 1.02”
LX54G Thin long nose smooth pliers
• Each jaw is smooth with beveled edges
• OAL 5.25” Jaw 1.02”
NX54 Slim needle nose serrated pliers
• Each jaw is serrated with beveled edges
• OAL 5.25” Jaw 1.02”
NX54G Slim needle nose smooth pliers
• Each jaw is smooth with beveled edges
• OAL 5.25” Jaw 1.02”
DX54G Flat nose smooth pliers
• Strongest gripping plier
• Ideal for straightening flat leads
• OAL 5.25” Jaw 1.02”
RX54 Round nose smooth jaw pliers
• Used to form perfectly round loops without deformation
• OAL 5.25” Jaw 1.02”
CX54G Curve nose smooth jaw pliers
• A very ergonomic alternative to long nose pliers
• Each jaw is smooth with beveled edges
• Permits most comfortable arm position for working
• OAL 5.25” Jaw 1.03”
19
19
13190 catalog pgs 6/30/08 9:23 AM Page 19
Products related to this Datasheet
CUTTER SIDE OVAL FLUSH 4.25"
PLIERS ELEC LONG NOSE 5.25"
CUTTER SIDE OVAL FLUSH 4.25"
PLIERS ELEC NEEDLE NOSE 4.5"
PLIERS ELEC LONG NOSE 4.5"
CUTTER ANGLE END FLSH
PLIER CURVE NOSE SMOOTH
PLIER FLAT NOSE SMOOTH
CUTTER ANGLE END FLSH
PLIER LONG NOSE SMOOTH
CUTTER OVAL SEMI FLSH
CUTTER TAPER FLSH
PLIER NEEDLE NOSE SERRATED
PLIER NEEDLE NOSE SMOOTH