JPY | USD

BK Series, Chip Bead Inductors Catalog

Taiyo Yuden

View All Related Products | Download PDF Datasheet

Datasheet

Notice for TAIYO YUDEN Products
[ For General Electronic Equipment
(General Environment) ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter TAIYO YUDENs official sales channel ). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDENs official sales
channel.
Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to U.S. Export
Administration Regulations , Foreign Exchange and Foreign Trade Control Law of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
i_mlci_BK_e-E05R01
MULTILAYER CHIP BEAD INDUCTORSBK SERIES
WAVE*
REFLOW
*Except for BK0402, BK0603, BK1005
PARTS NUMBER * Operating Temp.:-55~+125℃
B K 1 6 0 8 H S 1 2 1 T △=Blank space
①Series name
Code Series name
BK△ Multilayer chip bead inductor
②Dimensions(L×W)
Code Type(inch) Dimensions
(L×W)[mm]
0402 0402(01005) 0.4×0.2
0603 0603(0201) 0.6×0.3
1005 1005(0402) 1.0×0.5
1608 1608(0603) 1.6×0.8
2125 2125(0805) 2.0×1.25
③Material
Code Material
HW
Refer to impedance curves
for material differences
HS
HR
HM
LM
LL
TS
TM
④Nominal impedance
Code
(example) Nominal impedance[Ω
150 15
101 100
102 1000
⑤Characteristics
Code Characteristics
Standard
⑥Packaging
Code Packaging
T Taping
⑦Internal code
Code Internal code
Standard
STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
W
L
e
T
Type L W T e Standard quantity[pcs]
Paper tape Embossed tape
BK 0402
(01005)
0.40±0.02
(0.016±0.001)
0.20±0.02
(0.008±0.001)
0.20±0.02
(0.008±0.001)
0.10+0.04/-0.03
(0.004+0.002/-0.001) 20000
BK 0603
(0201)
0.60±0.03
(0.024±0.001)
0.30±0.03
(0.012±0.001)
0.30±0.03
(0.012±0.001)
0.15±0.05
(0.006±0.002) 15000
BK 1005
(0402)
1.00±0.05
(0.039±0.002)
0.50±0.05
(0.020±0.002)
0.50±0.05
(0.020±0.002)
0.25±0.10
(0.010±0.004) 10000
BK 1608
(0603)
1.6±0.15
(0.063±0.006)
0.8±0.15
(0.031±0.006)
0.8±0.15
(0.031±0.006)
0.3±0.2
(0.012±0.008) 4000
BK 2125
(0805)
2.0+0.3/-0.1
(0.079+0.012/-0.004)
1.25±0.2
(0.049±0.008)
0.85±0.2
(0.033±0.008)
0.5±0.3
(0.020±0.012) 4000
2.0+0.3/-0.1
(0.079+0.012/-0.004)
1.25±0.2
(0.049±0.008)
1.25±0.2
(0.049±0.008)
0.5±0.3
(0.020±0.012) 2000
Unit:mm(inch)
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
MULTILAYER CHIP BEAD INDUCTORS(BK SERIES)
REFLOWWAV E*
Except for BK0402, BK0603, BK1005
115
PARTS NUMBER
BK 0402
BK 0402HS100-T RoHS 10 ±5Ω 100 0.10 540 0.20 ±0.02
BK 0402HS700-T RoHS 70 ±25% 100 0.37 280 0.20 ±0.02
BK 0402HS121-T RoHS 120 ±25% 100 0.53 240 0.20 ±0.02
BK 0402HM100-T RoHS 10 ±5Ω 100 0.07 750 0.20 ±0.02
BK 0402HM750-T RoHS 75 ±25% 100 0.45 260 0.20 ±0.02
BK 0402HM121-T RoHS 120 ±25% 100 0.60 220 0.20 ±0.02
BK 0402HM151-T RoHS 150 ±25% 100 0.65 200 0.20 ±0.02
BK 0402HM181-T RoHS 180 ±25% 100 0.75 200 0.20 ±0.02
BK 0402HM241-T RoHS 240 ±25% 100 0.90 200 0.20 ±0.02
BK 0402HM331-T RoHS 330 ±25% 100 1.20 150 0.20 ±0.02
BK 0402LL220-T RoHS 22 ±25% 100 0.70 150 0.20 ±0.02
BK 0402LL470-T RoHS 47 ±25% 100 1.10 120 0.20 ±0.02
BK 0402LL101-T RoHS 100 ±25% 100 2.00 100 0.20 ±0.02
BK 0603
BK 0603HS220-T RoHS 22 ±25% 100 0.065 500 0.30 ±0.03
BK 0603HS330-T RoHS 33 ±25% 100 0.070 500 0.30 ±0.03
BK 0603HS800-T RoHS 80 ±25% 100 0.40 200 0.30 ±0.03
BK 0603HS121-T RoHS 120 ±25% 100 0.45 200 0.30 ±0.03
BK 0603HS241-T RoHS 240 ±25% 100 0.65 200 0.30 ±0.03
BK 0603HS601-T RoHS 600 ±25% 100 1.20 150 0.30 ±0.03
BK 0603HM600-T RoHS 60 ±25% 100 0.25 200 0.30 ±0.03
BK 0603HM121-T RoHS 120 ±25% 100 0.40 200 0.30 ±0.03
BK 0603HM241-T RoHS 240 ±25% 100 0.80 200 0.30 ±0.03
BK 0603HM471-T RoHS 470 ±25% 100 1.05 100 0.30 ±0.03
BK 0603HM601-T RoHS 600 ±25% 100 1.20 100 0.30 ±0.03
BK 0603HR121-T RoHS 120 ±25% 100 0.23 450 0.30 ±0.03
BK 0603HR241-T RoHS 240 ±25% 100 0.38 350 0.30 ±0.03
BK 0603HR601-T RoHS 600 ±25% 100 0.80 250 0.30 ±0.03
BK 0603HR102-T RoHS 1000 ±25% 100 1.15 220 0.30 ±0.03
BK 0603HR122-T RoHS 1200 ±25% 100 1.30 200 0.30 ±0.03
BK 0603LL100-T RoHS 10 ±25% 100 0.25 200 0.30 ±0.03
BK 0603LL220-T RoHS 22 ±25% 100 0.45 200 0.30 ±0.03
BK 0603LL330-T RoHS 33 ±25% 100 0.55 150 0.30 ±0.03
BK 0603LL470-T RoHS 47 ±25% 100 0.70 150 0.30 ±0.03
BK 0603LL560-T RoHS 56 ±25% 100 1.00 100 0.30 ±0.03
BK 0603LL800-T RoHS 80 ±25% 100 1.30 100 0.30 ±0.03
BK 0603LL121-T RoHS 120 ±25% 100 1.50 100 0.30 ±0.03
BK 0603TS800-T RoHS 80 ±25% 100 0.18 500 0.30 ±0.03
BK 0603TS121-T RoHS 120 ±25% 100 0.23 450 0.30 ±0.03
BK 0603TS241-T RoHS 240 ±25% 100 0.32 400 0.30 ±0.03
BK 0603TS601-T RoHS 600 ±25% 100 0.75 270 0.30 ±0.03
BK 0603TM800-T RoHS 80 ±25% 100 0.18 450 0.30 ±0.03
BK 0603TM121-T RoHS 120 ±25% 100 0.23 400 0.30 ±0.03
BK 0603TM241-T RoHS 240 ±25% 100 0.38 300 0.30 ±0.03
BK 0603TM601-T RoHS 600 ±25% 100 0.85 250 0.30 ±0.03
BK 1005
BK 1005HW680-T RoHS 68 ±25% 100 0.17 500 0.50 ±0.05
BK 1005HW121-T RoHS 120 ±25% 100 0.24 450 0.50 ±0.05
BK 1005HW241-T RoHS 240 ±25% 100 0.31 400 0.50 ±0.05
BK 1005HW431-T RoHS 430 ±25% 100 0.50 350 0.50 ±0.05
BK 1005HW601-T RoHS 600 ±25% 100 0.60 300 0.50 ±0.05
BK 1005HS100-T RoHS 10 ±25% 100 0.03 1,000 0.50 ±0.05
BK 1005HS330-T RoHS 33 ±25% 100 0.06 700 0.50 ±0.05
BK 1005HS680-T RoHS 68 ±25% 100 0.10 700 0.50 ±0.05
BK 1005HS800-T RoHS 80 ±25% 100 0.10 700 0.50 ±0.05
BK 1005HS121-T RoHS 120 ±25% 100 0.20 500 0.50 ±0.05
BK 1005HS241-T RoHS 240 ±25% 100 0.30 400 0.50 ±0.05
BK 1005HS431-T RoHS 430 ±25% 100 0.45 350 0.50 ±0.05
BK 1005HS601-T RoHS 600 ±25% 100 0.55 300 0.50 ±0.05
BK 1005HS102-T RoHS 1000 ±25% 100 0.58 300 0.50 ±0.05
BK 1005HR601-T RoHS 600 ±25% 100 0.60 300 0.50 ±0.05
BK 1005HM750-T RoHS 75 ±25% 100 0.18 350 0.50 ±0.05
BK 1005HM121-T RoHS 120 ±25% 100 0.18 300 0.50 ±0.05
BK 1005HM241-T RoHS 240 ±25% 100 0.30 300 0.50 ±0.05
BK 1005HM471-T RoHS 470 ±25% 100 0.45 250 0.50 ±0.05
BK 1005HM601-T RoHS 600 ±25% 100 0.50 250 0.50 ±0.05
BK 1005HM102-T RoHS 1000 ±25% 100 0.70 150 0.50 ±0.05
BK 1005LL100-T RoHS 10 ±25% 100 0.11 500 0.50 ±0.05
BK 1005LL220-T RoHS 22 ±25% 100 0.18 400 0.50 ±0.05
BK 1005LL330-T RoHS 33 ±25% 100 0.25 400 0.50 ±0.05
BK 1005LL470-T RoHS 47 ±25% 100 0.33 350 0.50 ±0.05
BK 1005LL680-T RoHS 68 ±25% 100 0.31 400 0.50 ±0.05
BK 1005LL121-T RoHS 120 ±25% 100 0.45 350 0.50 ±0.05
BK 1005LL181-T RoHS 180 ±25% 100 0.50 300 0.50 ±0.05
BK 1005LL241-T RoHS 240 ±25% 100 0.70 250 0.50 ±0.05
BK 1005LM182-T RoHS 1800 ±25% 100 0.90 120 0.50 ±0.05
Measuring frequency
[MHz]
DC Resistance
[Ω](max.)
Rated current
[mA](max.)
Thickness
[mm]
Parts number EHS Nominal impedance
[Ω] Impedance tolerance
Measuring frequency
[MHz]
DC Resistance
[Ω](max.)
Rated current
[mA](max.)
Thickness
[mm]
Parts number EHS Nominal impedance
[Ω] Impedance tolerance
Thickness
[mm]
Parts number EHS Nominal impedance
[Ω] Impedance tolerance DC Resistance
[Ω](max.)
Rated current
[mA](max.)
Measuring frequency
[MHz]
i_mlci_BK_e-E05R01
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
116
PARTS NUMBER
BK 1608
BK 1608HW121-T RoHS 120 ±25% 100 0.15 600 0.80 ±0.15
BK 1608HW241-T RoHS 240 ±25% 100 0.25 450 0.80 ±0.15
BK 1608HW431-T RoHS 430 ±25% 100 0.30 400 0.80 ±0.15
BK 1608HW601-T RoHS 600 ±25% 100 0.40 300 0.80 ±0.15
BK 1608HS220-T RoHS 22 ±25% 100 0.05 1,500 0.80 ±0.15
BK 1608HS330-T RoHS 33 ±25% 100 0.08 1,200 0.80 ±0.15
BK 1608HS470-T RoHS 47 ±25% 100 0.10 900 0.80 ±0.15
BK 1608HS600-T RoHS 60 ±25% 100 0.10 800 0.80 ±0.15
BK 1608HS800-T RoHS 80 ±25% 100 0.10 600 0.80 ±0.15
BK 1608HS121-T RoHS 120 ±25% 100 0.18 500 0.80 ±0.15
BK 1608HS241-T RoHS 240 ±25% 100 0.25 400 0.80 ±0.15
BK 1608HS601-T RoHS 600 ±25% 100 0.45 350 0.80 ±0.15
BK 1608HS102-T RoHS 1000 ±25% 100 0.60 300 0.80 ±0.15
BK 1608HM121-T RoHS 120 ±25% 100 0.20 350 0.80 ±0.15
BK 1608HM241-T RoHS 240 ±25% 100 0.35 300 0.80 ±0.15
BK 1608HM471-T RoHS 470 ±25% 100 0.45 250 0.80 ±0.15
BK 1608HM601-T RoHS 600 ±25% 100 0.60 250 0.80 ±0.15
BK 1608HM102-T RoHS 1000 ±25% 100 0.70 200 0.80 ±0.15
BK 1608LL300-T RoHS 30 ±25% 100 0.20 500 0.80 ±0.15
BK 1608LL470-T RoHS 47 ±25% 100 0.30 400 0.80 ±0.15
BK 1608LL560-T RoHS 56 ±25% 100 0.30 400 0.80 ±0.15
BK 1608LL680-T RoHS 68 ±25% 100 0.35 300 0.80 ±0.15
BK 1608LL121-T RoHS 120 ±25% 100 0.50 300 0.80 ±0.15
BK 1608LL181-T RoHS 180 ±25% 100 0.65 250 0.80 ±0.15
BK 1608LL241-T RoHS 240 ±25% 100 0.80 250 0.80 ±0.15
BK 1608LL331-T RoHS 330 ±25% 100 0.85 200 0.80 ±0.15
BK 1608LL431-T RoHS 430 ±25% 100 0.85 200 0.80 ±0.15
BK 1608LL511-T RoHS 510 ±25% 100 0.90 200 0.80 ±0.15
BK 1608LL681-T RoHS 680 ±25% 100 1.00 150 0.80 ±0.15
BK 1608LM751-T RoHS 750 ±25% 100 0.60 300 0.80 ±0.15
BK 1608LM152-T RoHS 1500 ±25% 100 0.75 250 0.80 ±0.15
BK 1608LM182-T RoHS 1800 ±25% 100 0.85 200 0.80 ±0.15
BK 1608LM252-T RoHS 2500 ±25% 100 1.10 200 0.80 ±0.15
BK 1608TS431-T RoHS 430 ±25% 100 0.21±30% 400 0.80 ±0.15
BK 1608TS601-T RoHS 600 ±25% 100 0.27±30% 350 0.80 ±0.15
BK 1608TS102-T RoHS 1000 ±25% 100 0.30±30% 300 0.80 ±0.15
BK 2125
BK 2125HS150-T RoHS 15 ±25% 100 0.05 1,200 0.85 ±0.2
BK 2125HS220-T RoHS 22 ±25% 100 0.05 1,200 0.85 ±0.2
BK 2125HS330-T RoHS 33 ±25% 100 0.05 1,200 0.85 ±0.2
BK 2125HS470-T RoHS 47 ±25% 100 0.05 1,000 0.85 ±0.2
BK 2125HS750-T RoHS 75 ±25% 100 0.10 1,000 0.85 ±0.2
BK 2125HS101-T RoHS 100 ±25% 100 0.10 900 0.85 ±0.2
BK 2125HS121-T RoHS 120 ±25% 100 0.15 800 0.85 ±0.2
BK 2125HS241-T RoHS 240 ±25% 100 0.20 600 0.85 ±0.2
BK 2125HS431-T RoHS 430 ±25% 100 0.25 500 0.85 ±0.2
BK 2125HS601-T RoHS 600 ±25% 100 0.30 500 0.85 ±0.2
BK 2125HS102-T RoHS 1000 ±25% 100 0.40 300 0.85 ±0.2
BK 2125HM121-T RoHS 120 ±25% 100 0.15 800 0.85 ±0.2
BK 2125HM241-T RoHS 240 ±25% 100 0.20 600 0.85 ±0.2
BK 2125HM471-T RoHS 470 ±25% 100 0.25 500 0.85 ±0.2
BK 2125HM601-T RoHS 600 ±25% 100 0.25 500 0.85 ±0.2
BK 2125HM102-T RoHS 1000 ±25% 100 0.35 400 0.85 ±0.2
BK 2125LL560-T RoHS 56 ±25% 100 0.20 600 0.85 ±0.2
BK 2125LL121-T RoHS 120 ±25% 100 0.30 400 0.85 ±0.2
BK 2125LL241-T RoHS 240 ±25% 100 0.35 300 0.85 ±0.2
BK 2125LM751-T RoHS 750 ±25% 100 0.30 400 0.85 ±0.2
BK 2125LM152-T RoHS 1500 ±25% 100 0.35 400 0.85 ±0.2
BK 2125LM182-T RoHS 1800 ±25% 100 0.45 300 1.25 ±0.2
BK 2125LM252-T RoHS 2500 ±25% 100 0.75 200 1.25 ±0.2
Measuring frequency
[MHz]
DC Resistance
[Ω](max.)
Rated current
[mA](max.)
Thickness
[mm]
Parts number EHS Nominal impedance
[Ω] Impedance tolerance
Measuring frequency
[MHz]
DC Resistance
[Ω](max.)
Rated current
[mA](max.)
Thickness
[mm]
Parts number EHS Nominal impedance
[Ω] Impedance tolerance
i_mlci_BK_e-E05R01
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
117
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
118
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 HS121
Impedance
30
25
20
15
10
5
0100 100001000101
Frequency [MHz]
BK0402 HM100
Impedance
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 HM750
Impedance
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 HM121
Impedance
350
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 HM151
Impedance
450
400
350
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0402 HM181
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 LL220
Impedance
400
350
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0402 LL470
700
600
500
400
300
200
100
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0402 LL101
500
400
300
200
100
0100 100001000101
Frequency [MHz]
BK0402 HM241
Impedance
700
600
500
400
300
200
100
0100 100001000101
Frequency [MHz]
BK0402 HM331
Impedance
100
80
60
40
20
0100 100001000101
Frequency [MHz]
BK0402 HS100
Impedance
250
200
150
100
50
0100 100001000101
Frequency [MHz]
BK0402 HS700
Impedance
BK0402
R
X
Z
100 100001000101
250
200
150
100
50
100
80
60
40
20
0100 100001000101
Frequency [MHz]
BK0603 HS220
Impedance
BK0603 HS330
100
80
60
40
20
100101 1000 10000
Frequency MHz
Impedance
R
X
0
Z
R
X
Z
100 100001000101
250
200
150
100
50
BK0603
100 100001000101
250
200
150
100
50
100 100001000101
250
200
150
100
50
100 100001000101
BK0603 HS601
1000
800
600
400
200
0
Frequency MHz
Impedance
100 100001000101
Z
R
X
BK0603 HM241
500
400
300
200
100
0
Frequency MHz
Impedance
100 100001000101
Z
X
R
BK0603 HM471
Frequency MHz
Impedance
1000
800
600
400
200
0
100 100001000101
Z
R
BK0603 HM601
Impedance[ ]
1000
800
600
400
200
0
Z
R
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
119
BK1005 HW121
250
200
150
100
50
0
Frequency MHz
Impedance
100101 1000 10000
BK1005 HW241
500
400
300
200
100
0
Frequency MHz
Impedance
100101 1000 10000
R
X
Z
BK1005 HW431
1000
800
600
400
200
0
Frequency MHz
Impedance
100101 1000 10000
R
X
Z
BK1005 HW680
Frequency MHz
Impedance
250
200
150
100
50
0100101 1000 10000
R
X
Z
BK1005
BK0603 TS241
500
400
300
200
100
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 TS121
250
200
150
100
50
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 TS800
200
150
100
50
0100101 1000 10000
Frequency MHz
Impedance
R
X
Z
BK0603 TS601
1000
800
600
400
200
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 TM241
500
400
300
200
100
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 TM601
1000
800
600
400
200
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 LL560
500
400
300
200
100
0100101 1000 10000
Frequency MHz
Impedance
Z
R
X
BK0603 LL800
1000
800
600
400
200
0100101 1000 10000
Frequency MHz
Impedance
Z
R
X
BK0603 LL121
1000
800
600
400
200
0100101 1000 10000
Frequency MHz
Impedance
Z
BK0603 LL220
Frequency MHz
Impedance
250
200
150
100
50
0100 100001000101
Z
BK0603 LL330
Frequency MHz
Impedance
500
400
300
200
100
0100 100001000101
X
Z
BK0603 LL470
500
400
300
200
100
0100101 1000 10000
Frequency MHz
Impedance
R
X
Z
BK0603 LL100
Frequency MHz
Impedance
250
200
150
100
50
0100 100001000101
Z
R
X
BK0603 TM800
200
150
100
50
0100101 1000 10000
Frequency MHz
Impedance
R
X
Z
BK0603 TM121
250
200
150
100
50
0
Frequency MHz
Impedance
100101 1000 10000
BK0603 HR102
Impedance[ ]
1500
1000
500
0
Z
R
BK0603 HR122
Impedance[ ]
2000
1500
1000
500
0
Z
R
1000
900
800
700
600
500
400
300
200
100
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0603 HR601
200
180
160
140
120
100
80
40
20
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0603 HR121
400
350
300
250
200
150
100
50
0100 100001000101
Frequency [MHz]
Impedance
100 100001000101
BK0603 HR241
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
120
BK1005 HW601
1000
800
600
400
200
0
Frequency MHz
Impedance
100101 1000 10000
R
X
Z
BK1005 HS100
100
80
60
40
20
0
Frequency MHz
Impedance
100101 1000 10000
RX
Z
BK1005 HS330
100
80
60
40
20
0
Impedance
100101 1000 10000
Frequency MHz
R
X
Z
BK1005 HS680
250
200
150
100
50
0
Frequency MHz
Impedance
100 100001000101
X
Z
250
200
150
100
50
0
BK1005 HS800
250
200
150
100
50
0
Frequency MHz
Impedance
100101 1000 10000
R
X
Z
BK1005 HS431
1000
800
600
400
200
0100101 100001000
Frequency MHz
Impedance
RR
X
Z
Z
RR
X
Z
Z
BK1005 HS102
2000
1000
01000100101 10000
Frequency MHz
Impedance
BK1005 HR601
1000
800
600
400
200
0
BK1005 HM750
200
150
100
50
0
BK1005 HM121
250
200
150
100
50
0100 1000101 10000
Frequency MHz
Impedance
RR
X
Z
500
100
200
300
400
110 100 1000 10000
0
2000
1000
0
110 1000100 10000
BK1005 HM102
250
150
200
100
50
0
110 100 1000 10000
BK1005 LL100 250
200
150
100
50
0
110 100 1000 10000
BK1005 LL220
500
400
300
200
100
0
110 100 1000 10000
BK1005 LL330
500
400
300
200
100
0
110 100 1000 10000
BK1005 LL470
500
400
300
200
100
0
110 100 1000 10000
BK1005 LL680
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
121
500
250
0
110 100 1000 10000
BK1608 LL300
500
250
0
110 100 1000 10000
BK1608 LL470
500
250
0
110 100 1000 10000
BK1608 LL560
500
250
0
110 100 1000 10000
BK1608 LL680
BK1608
2500
2000
1500
1000
500
0
110 100 100001000
BK1005 LM182
RR
X
Z
Z
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
122
1500
750
0
110 100 1000
BK1608 LL121
2000
4000
BK2125
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS
ELECTRICAL CHARACTERISTICS
123
R
Z
X
1000100101
0
500
1000
R
Z
1000100101
0
500
1000
X
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E06R01
Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils(MC series F type)
Metal Multilayer Chip Power Inductors (MCOILTM MC series)
PACKAGING
①Minimum Quantity
Tape & Reel Packaging
Type Thickness
mm(inch)
Standard Quantity [pcs]
Paper Tape Embossed Tape
CK1608(0603) 0.8 (0.031) 4000
CK2125(0805) 0.85(0.033) 4000
1.25(0.049) 2000
CKS2125(0805) 0.85(0.033) 4000
1.25(0.049) 2000
CKP1608(0603) 0.8 (0.031) 4000
CKP2012(0805) 0.9 (0.035) 3000
CKP2016(0806) 0.9 (0.035) 3000
CKP2520(1008)
0.7 (0.028) 3000
0.9 (0.035) 3000
1.1 (0.043) 2000
NM2012(0805) 0.9 (0.035) 3000
NM2520(1008) 0.9 (0.035) 3000
1.1 (0.043) 2000
LK1005(0402) 0.5 (0.020) 10000
LK1608(0603) 0.8 (0.031) 4000
LK2125(0805) 0.85(0.033) 4000
1.25(0.049) 2000
HK0603(0201) 0.3 (0.012) 15000
HK1005(0402) 0.5 (0.020) 10000
HK1608(0603) 0.8 (0.031) 4000
HK2125(0805) 0.85(0.033) 4000
1.0 (0.039) 3000
HKQ0402(01005) 0.2 (0.008) 20000 40000
HKQ0603W(0201) 0.3 (0.012) 15000
HKQ0603S(0201) 0.3 (0.012) 15000
HKQ0603U(0201) 0.3 (0.012) 15000
AQ105(0402) 0.5 (0.020) 10000
BK0402(01005) 0.2 (0.008) 20000
BK0603(0201) 0.3 (0.012) 15000
BK1005(0402) 0.5 (0.020) 10000
BKH0603(0201) 0.3 (0.012) 15000
BKH1005(0402) 0.5 (0.020) 10000
BK1608(0603) 0.8 (0.031) 4000
BK2125(0805) 0.85(0.033) 4000
1.25(0.049) 2000
BK2010(0804) 0.45(0.018) 4000
BK3216(1206) 0.8 (0.031) 4000
BKP0402(01005) 0.2 (0.008) 20000
BKP0603(0201) 0.3 (0.012) 15000
BKP1005(0402) 0.5 (0.020) 10000
BKP1608(0603) 0.8 (0.031) 4000
BKP2125(0805) 0.85(0.033) 4000
MCF0605(0202) 0.3 (0.012) 15000
MCF0806(0302) 0.4 (0.016) 10000
MCF1210(0504) 0.55(0.022) 5000
MCF2010(0804) 0.45(0.018) 4000
MCFK1608(0603) 0.6 (0.024) 4000
MCFE1608(0603) 0.65(0.026) 4000
MCKK1608(0603) 1.0(0.039) 3000
MCHK2012(0806) 0.8 (0.031) 4000
MCKK2012(0805) 1.0(0.039) - 3000
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E06R01
②Taping material
Card board carrier tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
Chip Filled
Chip
CK 1608
CKP 1608
CK 2125
CKS 2125
LK 1005
LK 1608
LK 2125
HK 0603
HK 1005
HK 1608
HKQ 0402
HKQ 0603
AQ 105
BK 0402
BK 0603
BK 1005
BK 1608
BK 2125
BK 2010
BKP 0402
BKP 0603
BKP 1005
BKP 1608
BKP 2125
BKH 0603
BKH 1005
MCF 0605
MC 1608
MC 2012
Embossed Tape
Top tape
Base tape
Sprocket hole
Chip cavity
Chip Filled
Chip
CK 2125
CKS 2125
CKP 2012
CKP 2016
CKP 2520
NM 2012
NM 2520
LK 2125
HKQ 0402
HK 2125
BK 2125
BK 3216
MCF 0806
MCF 1210
MCF 2010
MC 1608
MC 2012
③Taping Dimensions
Paper tape (8mm wide) Unit:mm(inch)
F
2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
T
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E06R01
Type Thickness
mm(inch)
Chip cavity Insertion Pitch Tape Thickness
CK1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
CK2125(0805) 0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
CKS2125(0805) 0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
CKP1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
LK1005(0402) 0.5 (0.020) 0.65±0.1
(0.026±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
LK1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
LK2125(0805) 0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
HK0603(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
HK1005(0402) 0.5 (0.020) 0.65±0.1
(0.026±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
HK1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
HKQ0402(01005) 0.2 (0.008) 0.25±0.04
(0.010±0.002)
0.45±0.04
(0.018±0.002)
2.0±0.05
(0.079±0.002)
0.36max
(0.014max)
HKQ0603W(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
HKQ0603S(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
HKQ0603U(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
AQ105(0402) 0.5 (0.020) 0.75±0.1
(0.030±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
BK0402(01005) 0.2 (0.008) 0.25±0.04
(0.010±0.002)
0.45±0.04
(0.018±0.002)
2.0±0.05
(0.079±0.002)
0.36max
(0.014max)
BK0603(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
BK1005(0402) 0.5 (0.020) 0.65±0.1
(0.026±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
BK1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
BK2125(0805) 0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
BK2010(0804) 0.45(0.018) 1.2±0.1
(0.047±0.004)
2.17±0.1
(0.085±0.004)
4.0±0.1
(0.157±0.004)
0.8max
(0.031max)
BKP0402(01005) 0.2 (0.008) 0.25±0.04
(0.010±0.002)
0.45±0.04
(0.018±0.002)
2.0±0.05
(0.079±0.002)
0.36max
(0.014max)
BKP0603(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
BKP1005(0402) 0.5 (0.020) 0.65±0.1
(0.026±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
BKP1608(0603) 0.8 (0.031) 1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
BKP2125(0805) 0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.1max
(0.043max)
BKH0603(0201) 0.3 (0.012) 0.40±0.06
(0.016±0.002)
0.70±0.06
(0.028±0.002)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
BKH1005(0402) 0.5 (0.020) 0.65±0.1
(0.026±0.004)
1.15±0.1
(0.045±0.004)
2.0±0.05
(0.079±0.002)
0.8max
(0.031max)
MCF0605(0202) 0.3 (0.012) 0.62±0.03
(0.024±0.001)
0.77±0.03
(0.030±0.001)
2.0±0.05
(0.079±0.002)
0.45max
(0.018max)
MCFK1608(0603) 0.6 (0.024) 1.1±0.05
(0.043±0.002)
1.9±0.05
(0.075±0.002)
4.0±0.1
(0.157±0.004)
0.72max
(0.028max)
MCFE1608(0603) 0.65(0.026) 1.1±0.05
(0.043±0.002)
1.9±0.05
(0.075±0.002)
4.0±0.1
(0.157±0.004)
0.9max
(0.035max)
MCHK2012(0805) 0.8 (0.031) 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
0.9max
(0.035max)
Unit : mm(inch)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E06R01
Embossed Tape (8mm wide) Unitmminch
F
2.0±0.05
(0.079±0.002)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
Type Thickness
mm(inch)
Chip cavity Insertion Pitch Tape Thickness
K T
CK2125(0805) 1.25(0.049) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
2.0
(0.079)
0.3
(0.012)
CKS2125(0805) 1.25(0.049) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
2.0
(0.079)
0.3
(0.012)
CKP2012(0805) 0.9 (0.035) 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.3
(0.051)
0.3
(0.012)
CKP2016(0806) 0.9 (0.035) 1.8±0.1
(0.071±0.004)
2.2±0.1
(0.087±0.004)
4.0±0.1
(0.157±0.004)
1.3
(0.051)
0.25
(0.01)
CKP2520(1008)
0.7 (0.028)
2.3±0.1
(0.091±0.004)
2.8±0.1
(0.110±0.004)
4.0±0.1
(0.157±0.004)
1.4
(0.055)
0.3
(0.012)
0.9 (0.035) 1.4
(0.055)
1.1 (0.043) 1.7
(0.067)
NM2012(0805) 0.9 (0.035) 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.3
(0.051)
0.3
(0.012)
NM2520(1008)
0.9 (0.035) 2.3±0.1
(0.091±0.004)
2.8±0.1
(0.110±0.004)
4.0±0.1
(0.157±0.004)
1.4
(0.055) 0.3
(0.012)
1.1 (0.043) 1.7
(0.067)
LK2125(0805) 1.25(0.049) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
2.0
(0.079)
0.3
(0.012)
HK2125(0805)
0.85(0.033) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.5
(0.059) 0.3
(0.012)
1.0 (0.039) 2.0
(0.079)
BK2125(0805) 1.25(0.049) 1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
2.0
(0.079)
0.3
(0.012)
BK3216(1206) 0.8(0.031) 1.9±0.1
(0.075±0.004)
3.5±0.1
(0.138±0.004)
4.0±0.1
(0.157±0.004)
1.4
(0.055)
0.3
(0.012)
MCF0806(0302) 0.4 (0.016) 0.75±0.05
(0.030±0.002)
0.95±0.05
(0.037±0.002)
2.0±0.05
(0.079±0.002)
0.55
(0.022)
0.3
(0.012)
MCF1210(0504) 0.55(0.022) 1.15±0.05
(0.045±0.002)
1.40±0.05
(0.055±0.002)
4.0±0.1
(0.157±0.004)
0.65
(0.026)
0.3
(0.012)
MCF2010(0804) 0.45(0.018) 1.1±0.1
(0.043±0.004)
2.3±0.1
(0.091±0.004)
4.0±0.1
(0.157±0.004)
0.85
(0.033)
0.3
(0.012)
MCKK1608(0603) 1.0 (0.039) 1.1±0.1
(0.043±0.004)
1.95±0.1
(±0.004)
4.0±0.1
(0.157±0.004)
1.4
(0.055)
0.25
(0.01)
MCKK2012(0805) 1.0 (0.039) 1.55±0.2
(0.061±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.1
(0.157±0.004)
1.35
(0.053)
0.25
(0.010)
Unit : mm(inch)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E06R01
Embossed Tape (4mm wide) Unitmminch
F
1.0±0.02
(0.039±0.001)
2.0±0.04
(0.079±0.002)
0.9
0.05
(0.035±0.002)
1.8±0.02
(0.071±0.001)
4.0±0.05
(0.157±0.002)
φ0.8±0.04
(φ0.031±0.002)
Sprocket hole
B
A
Type Thickness
mm(inch)
Chip cavity Insertion Pitch Tape Thickness
K T
HKQ0402(01005) 0.2 (0.008) 0.23 0.43 1.0±0.02 0.5max. 0.25max.
Unit : mm
④LEADER AND BLANK PORTION
Blank portion Chip cavity Blank portion Leader
160mm or more
(6.3inches or more)
Direction of tape feed
100mm or more
(3.94inches or more)
400mm or more
(15.7inches or more)
⑤Reel Size
E
C
D
R B
t
A
W
A B C D E R
φ178±2.0 φ50 or more φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0
t W
4mm width tape 1.5max. 5±1.0
8mm width tape 2.5max. 10±1.5
(Unit : mm)
⑥Top tape strength
The top tape requires a peel-off force of 0.1~0.7N in the direction of the arrow as illustrated below.
0~15° Top tape
Base tape
Pull direction
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils(MC series F type)
Metal Multilayer Chip Power Inductors (MCOILTM MC series)
RELIABILITY DATA
1. Operating Temperature Range
Specified Value
BK0402
-55~+125℃
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
-55~+85℃
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
-40~+85℃
MCF 0806
MCF 1210
MCF 2010
CK1608
-40~+85℃
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HKQ0402
-55~+125℃
HK0603
HK1005
HK1608 -40~+85℃
HK2125
HKQ0603W/HKQ0603S/HKQ0603U -55~+125℃
AQ105
MCFK1608
MCFE1608
-40~+125℃(Including self-generated heat)
MCKK1608
MCHK2012
MCKK2012
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
2. Storage Temperature Range
Specified Value
BK0402
-55~+125℃
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
-55~+85℃
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
-40~+85℃
MCF 0806
MCF 1210
MCF 2010
CK1608
-40~+85℃
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HKQ0402
-55~+125℃
HK0603
HK1005
HK1608 -40~+85℃
HK2125
HKQ0603W/HKQ0603S/HKQ0603U -55~+125℃
AQ105
MCFK1608
MCFE1608
-40~+85℃
MCKK1608
MCHK2012
MCKK2012
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
3. Rated Current
Specified Value
BK0402 150~750mA DC
BK0603 100~500mA DC
BK1005 120~1000mA DC
BKH0603 115~450mA DC
BKH1005 200~300mA DC
BK1608 150~1500mA DC
BK2125 200~1200mA DC
ARRAY BK2010 100mA DC
BK3216 100~200mA DC
BKP0402 0.55~1.1A DC
BKP0603 0.8~1.8A DC
BKP1005 0.8~2.4A DC
BKP1608 1.0~3.0A DC
BKP2125 1.5~4.0A DC
MCF 0605 0.05A DC
MCF 0806 0.1~0.13A DC
MCF 1210 0.1~0.16A DC
MCF 2010 0.1A DC
CK1608 50~60mA DC
CK2125 60~500mA DC
CKS2125 110~280mA DC
CKP1608 0.35~0.9A DC
CKP2012 0.7~1.7A DC
CKP2016 0.9~1.6A DC
CKP2520 1.1~1.8A DC
NM2012 1.0~1.2A DC
NM2520 0.9~1.2A DC
LK1005 20~25mA DC
LK1608 1~150mA DC
LK2125 5~300mA DC
HK0603 60~470mA DC
HK1005 110~300mA DC (-55~+125℃) 200~900mA DC (-55~+85℃)
HK1608 150~300mA DC
HK2125 300mA DC
HKQ0402 100~500mA DC
HKQ0603W 100~850mA DC
HKQ0603S 130~600mA DC
HKQ0603U 190~900mA DC
AQ105 280~710mA DC
MCFK1608 Idc1 1500~2300mA DC, Idc2 900~2100mA DC
MCFE1608 Idc1 1400~2600mA DC, Idc2 800~1500mA DC
MCKK1608 Idc1 2800~2000mA DC Idc2 1300~2600mA DC
MCHK2012 Idc1 2260~4320mA DC, Idc2 1470~3600mA DC
MCKK2012 Idc1 3600~6200mA DC, Idc2 2100~4000mA DC
Definition of rated current:
・In the CK, CKS and BK Series, the rated current is the value of current at which the temperature of the element is increased within 20℃.
・In the BK Series P type, CK Series P type, NM Series, the rated current is the value of current at which the temperature of the element is increased within 40℃.
・In the LK, HK, HKQ0603, and AQ Series, the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of
current at which the temperature of the element is increased within 20℃.
・In the HKQ0402(~9N1), the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of current at which the
temperature of the element is increased within 20℃.
・In the HKQ0402(10N~), the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of current at which the
temperature of the element is increased within 25℃.
・In the MC Series, Idc1 is the DC value at which the initial L value is decreased within 30% and Idc2 is the DC value at which the temperature of element is increased within 40℃ by
the application of DC bias. (at 20℃)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
4. Impedance
Specified Value
BK0402 10~330Ω ±5Ω(10Ω), ±25%(Other)
BK0603 10~1200Ω ±25%
BK1005 10~1800Ω ±25%
BKH0603 25~1500Ω ±25%
BKH1005 600~1800Ω ±25%
BK1608 22~2500Ω ±25%
BK2125 15~2500Ω ±25%
ARRAY BK2010 5~1000Ω ±25%
BK3216 60~100 ±25%
BKP0402 10~33Ω ±5Ω(10Ω)、±25%(Other)
BKP0603 10~120Ω ±5Ω(10Ω), ±25%(Other)
BKP1005 10~330Ω ±5Ω(EM100), ±25%(Other)
BKP1608 33~470Ω ±25%
BKP2125 33~330Ω ±25%
MCF 0605 12~90Ω ±5Ω(12Ω), ±20%(35Ω,90Ω),±25%(60Ω)
MCF 0806 12~90Ω ±5Ω(12Ω), ±20%(47Ω,90Ω),±25%(30Ω)
MCF 1210 40~90Ω ±20%(2H900),±25%(Other)
MCF 2010 90Ω ±25%
CK1608
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HKQ0402
HK0603
HK1005
HK1608
HK2125
HKQ0603W/HKQ0603S/HKQ0603U
AQ105
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
BK0402Series, BKP0402Series
Measuring frequency : 100±1MHz
Measuring equipment : E4991A(or its equivalent)
Measuring jig : 16197A(or its equivalent)
BK0603Series, BKP0603Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A(or its equivalent)
Measuring jig : 16193A(or its equivalent)
BK1005Series, BKP1005Series ,BKH1005Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A(or its equivalent)
Measuring jig : 16192A(or its equivalent), 16193A(or its equivalent)
BK1608・2125Series, BKP1608・2125Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A(or its equivalent), 4195A(or its equivalent)
Measuring jig : 16092A(or its equivalent) or 16192A(or its equivalent)/HW
BK2010・3216Series, MCF Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A(or its equivalent), 4195A(or its equivalent)
Measuring jig : 16192A(or its equivalent)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
5. Inductance
Specified Value
BK0402
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608 4.7~10.H: ±20%
CK2125 0.1~10.H: ±20%
CKS2125 1.0~10.0μH: ±20%
CKP1608 0.33~2.2μH: ±20%
CKP2012 0.47~4.7μH: ±20%
CKP2016 0.47~4.7μH: ±20%
CKP2520 0.47~4.7μH: ±20%
NM2012 0.82~1.0μH: ±20%
NM2520 1.0~2.2μH: ±20%
LK1005 0.12~2.2μH: ±10 or 20%
LK1608 0.047~33.0μH: ±20% 0.10~12.0μH: ±10%
LK2125 0.047~33.0μH: ±20% 0.10~12.0μH: ±10%
HK0603 1.0~6.2nH: ±0.3nH 6.8~100nH: ±5%
HK1005 1.0~6.2nH: ±0.3nH 6.8~270nH: ±5%
HK1608 1.0~5.6nH: ±0.3nH 6.8~470nH: ±5%
HK2125 1.5~5.6nH: ±0.3nH 6.8~470nH: ±5%
HKQ0402 0.5~3.9nH: ±0.1 or 0.2 or 0.3nH 4.3~5.6nH: ±0.3nH or 3% or 5%
6.2~47nH ±3 or 5%
HKQ0603W 0.6~3.9nH: ±0.1 or 0.2 or 0.3nH 4.3~6.2nH: ±0.2 or 0.3nH or 3 or 5%
6.8~30nH ±3 or 5% 33~100nH ±5%
HKQ0603S 0.6~6.2nH: ±0.2 or 0.3nH 6.8~22nH: ±3 or 5%
HKQ0603U 0.6~4.2nH: ±0.1 or 0.2 or 0.3nH 4.3~6.5nH: ±0.2 or 0.3nH 6.8~22nH: ±3 or 5%
AQ105 1.0~6.2nH: ±0.3nH 6.8~15nH: ±5%
MCFK1608 0.24~1.0μH: ±20%
MCFE1608 0.24~1.H: ±20%
MCKK1608 0.24~1.0μH: ±20%
MCHK2012 0.24~1.0μH: ±20%
MCKK2012 0.24~1.0μH: ±20%
Test Methods and
Remarks
CK、LK、CKP、NM、MC Series
Measuring frequency : 2~4MHz(CK1608)
Measuring frequency : 2~25MHz(CK2125)
Measuring frequency : 2~10MHz(CKS2125)
Measuring frequency : 10~25MHz(LK1005)
Measuring frequency : 1~50MHz(LK1608)
Measuring frequency : 0.4~50MHz(LK2125)
Measuring frequency : 1MHz(CKP1608・CKP2012・CKP2016・CKP2520・NM2012・NM2520・MCFK1608・MCFE1608・MCHK2012・MCKK2012)
Measuring equipment /jig :・4194A+16085B+16092A(or its equivalent) ・4195A+41951+16092A(or its equivalent)
・4294A+16192A(or its equivalent) ・4291A+16193A(or its equivalent)/LK1005
4285A 42841A 42842C 42851 61100 or its equivalent /CKP1608 CKP2012・CKP2016・CKP2520・NM2012・
NM2520・MCFK1608・MCFE1608・MCKK1608・MCHK2012・MCKK2012
Measuring current :・1mA rms(0.047~4.7μH)
・0.1mA rms(5.6~33μH)
HK、HKQ、AQ Series
Measuring frequency : 100MHz(HK0603・HK1005・AQ105)
Measuring frequency : 50/100MHz(HK1608・HK2125
Measuring frequency : 500MHz(HKQ0603S・HKQ0603U)
Measuring frequency : 300/500MHz(HKQ0603W)
Measuring frequency : 100/500MHz(HKQ0402
Measuring equipment /jig :・4291A+16197A(or its equivalent)/HK0603・AQ105
・4291A+16193A(or its equivalent)/HK1005
・E4991A+16197A(or its equivalent)/HKQ0603S・HKQ0603U・HKQ0603W
・4291A+16092A in-house made jig(or its equivalent)/HK1608・HK2125
・E4991A+16196D(or its equivalent)/HKQ0402
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
6. Q
Specified Value
BK0402
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 10~20 min.
LK1608 10~35 min.
LK2125 15~50 min.
HK0603 4~5 min.
HK1005 8 min.
HK1608 8~12 min.
HK2125 10~18 min.
HKQ0402 3~8 min.
HKQ0603W 6~15 min.
HKQ0603S 10~13 min.
HKQ0603U 14 min.
AQ105 8 min.
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
LK Series
Measuring frequency : 10~25MHz(LK1005)
Measuring frequency : 1~50MHz(LK1608)
Measuring frequency : 0.4~50MHz(LK2125)
Measuring equipment /jig :・4194A+16085B+16092A(or its equivalent)
・4195A+41951+16092A(or its equivalent)
・4294A+16192A(or its equivalent)
・4291A+16193A(or its equivalent)/LK1005
Measuring current ・1mA rms(0.047~4.7μH)
・0.1mA rms(5.6~33μH)
HK、HKQ、AQ Series
Measuring frequency : 100MHz(HK0603・HK1005・AQ105)
Measuring frequency : 50/100MHz(HK1608・HK2125)
Measuring frequency : 500MHz(HKQ0603S・HKQ0603U)
Measuring frequency : 300/500MHz(HKQ0603W)
Measuring frequency : 100/500MHz(HKQ0402)
Measuring equipment /jig :・4291A+16197A(or its equivalent)/HK0603・AQ105
・4291A+16193A(or its equivalent)/HK1005
・E4991A+16197A(or its equivalent)/HKQ0603S・HKQ0603U・HKQ0603W
・4291A+16092A in-house made jig(or its equivalent)/HK1608, HK2125
・E4991A+16196D(or its equivalent)HKQ0402
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
7. DC Resistance
Specified Value
BK0402 0.07~1.2Ω max.
BK0603 0.065~1.50Ω max.
BK1005 0.03~0.9 max.
BKH0603 0.26~3.20Ω max.
BKH1005 0.85~2.00Ω max.
BK1608 0.05~1.1 max.
BK2125 0.05~0.7 max.
ARRAY BK2010 0.10~0.90Ω max.
BK3216 0.15~0.80Ω max.
BKP0402 0.05~0.15Ω max.
BKP0603 0.030~0.180Ω max.
BKP1005 0.0273~0.220Ω max.
BKP1608 0.025~0.18Ω max.
BKP2125 0.020~0.075Ω max.
MCF 0605 2.5~5.0Ω max
MCF 0806 1.5~5.0Ω max.
MCF 1210 1.5~4.5Ω max.
MCF 2010 4.5Ω max.
CK1608 0.45~0.85Ω±30%)
CK2125 0.16~0.65Ω max.
CKS2125 0.12~0.52Ω max.
CKP1608 0.15~0.35Ω max.
CKP2012 0.08~0.28Ω max.
CKP2016 0.075~0.20Ω max
CKP2520 0.05~0.16Ω max.
NM2012 0.10~0.15Ω max.
NM2520 0.11~0.22Ω max.
LK1005 0.41~1.16Ω max.
LK1608 0.2~2.2Ω max.
LK2125 0.1~1.1Ω max.
HK0603 0.11~3.74Ω max.
HK1005 0.08~4.8Ω max.
HK1608 0.05~2.6Ω max.
HK2125 0.10~1.5Ω max.
HKQ0402 0.08~5.0Ω max.
HKQ0603W 0.07~4.1Ω max.
HKQ0603S 0.06~1.29Ω max.
HKQ0603U 0.06~1.29Ω max.
AQ105 0.07~0.45Ω max.
MCFK1608 0.050~0.22 max.
MCFE1608 0.100~0.340Ω max.
MCKK1608 0.038~0.123Ω max.
MCHK2012 0.024~0.111Ω max.
MCKK2012 0.025~0.090Ω max.
Test Methods and
Remarks Measuring equipment:VOAC-7412, VOAC-7512, VOAC-7521(made by Iwasaki Tsushinki), HIOKI3227 (or its equivalent)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
8. Self Resonance Frequency(SRF)
Specified Value
BK0402
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608 17~25MHz min.
CK2125 24~235MHz min.
CKS2125 24~75MHz min.
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 40~180MHz min.
LK1608 9~260MHz min.
LK2125 13~320MHz min.
HK0603 900~10000MHz min.
HK1005 400~10000MHz min.
HK1608 300~10000MHz min.
HK2125 200~4000MHz min.
HKQ0402 1200~10000MHz min.
HKQ0603W 800~10000MHz min.
HKQ0603S 1900~10000MHz min.
HKQ0603U 1900~10000MHz min.
AQ105 2300~10000MHz min.
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
LK、CK Series :
Measuring equipment : 4195A(or its equivalent)
Measuring jig : 41951+16092A(or its equivalent)
HK、HKQ、AQ Series :
Measuring equipment : 8719C(or its equivalent)・8753D(or its equivalent)/HK2125
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
9. Temperature Characteristic
Specified Value
BK0402
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HK0603
Inductance change:Within ±10%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
HK、HKQ、AQ Series:
Temperature range : -30~+85℃
Reference temperature : +20℃
MC Series:
Temperature range : -40~+85℃
Reference temperature : +20℃
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
10. Resistance to Flexure of Substrate
Specified Value
BK0402
No mechanical damage.
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HK0603
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
Warp : 2mm(BK Series without 0402size、BKP、BKH1005、CK、CKS、CKP、LK、HK、HKQ0603S、HKQ0603U、
AQ Series、MCF1210、MC Series)
: 1mm(BK0402、BKP0402、BKH0603、HKQ0402、HKQ0603W、MCF Series without 1210 size,)
Testing board : glass epoxy-resin substrate
Thickness : 0.8mm
20
Warp
Board
(Unit:mm)
R-230
45 45
Deviation±1
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
11. Solderability
Specified Value
BK0402
At least 90% of terminal electrode is covered by new solder.
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
MCF 0806
MCF 1210
MCF 2010
CK1608
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005
LK1608
LK2125
HK0603
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
Solder temperature :230±5℃ (JIS Z 3282 H60A or H63A)
Solder temperature :245±3℃ (Sn/3.0Ag/0.5Cu)
Duration :4±1 sec.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
12. Resistance to Soldering
Specified Value
BK0402
Appearance:No significant abnormality
Impedance change:Within ±30%
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
Appearance:No significant abnormality
Impedance change:Within ±20%
MCF 0806
MCF 1210
MCF 2010
CK1608
Appearance:No significant abnormality
Inductance change
R10~4R7: Within ±10%
6R8~100: Within ±15%
CKS2125 Within ±20
CKP1608、CKP2012、CKP2016、CKP2520、NM2012、NM2520: Within ±30%
CK2125
CKS2125
CKP1608
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 Appearance:No significant abnormality
Inductance change: Within ±15%
LK1608 Appearance:No significant abnormality
Inductance change
47N~4R7: Within ±10%
5R6~330: Within ±15%
LK2125
HK0603
Appearance:No significant abnormality
Inductance change: Within ±5%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
Appearance:No significant abnormality
Inductance change: Within ±10%
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
Solder temperature :260±5℃
Duration :10±0.5 sec.
Preheating temperature :150 to 180℃
Preheating time 3 min.
Flux :Immersion into methanol solution with colophony for 3 to 5 sec.
Recovery :2 to 3 hrs of recovery under the standard condition after the test.(See Note 1)
(Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
13. Thermal Shock
Specified Value
BK0402
Appearance:No significant abnormality
Impedance change: Within ±30
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
Appearance:No significant abnormality
Impedance change: Within ±20
MCF 0806
MCF 1210
MCF 2010
CK1608 Appearance:No significant abnormality
Inductance change:Within ±20% Q change:Within ±30%
CK2125
CKS2125 Appearance:No significant abnormality
Inductance change:Within ±20%
CKP1608
Appearance:No significant abnormality
Inductance change: Within ±30%
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±30%
LK1608
LK2125
HK0603
Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±20%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
Appearance:No significant abnormality
Inductance change: Within ±10%
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
Conditions for 1 cycle
Step temperature(℃) time(min.)
1 Minimum operating temperature +0/-3 30±3
2 Room temperature 2~3
3 Maximum operating temperature +3/-0 30±3
4 Room temperature 2~3
Number of cycles:5
Recovery:2 to 3 hrs of recovery under the standard condition after the test.(See Note 1)
(Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
14. Damp Heat( Steady state)
Specified Value
BK0402
Appearance:No significant abnormality
Impedance change: Within ±30
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
Appearance:No significant abnormality
Impedance change: Within ±20
MCF 0806
MCF 1210
MCF 2010
CK1608 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
CK2125
CKS2125 Appearance:No significant abnormality
Inductance change: Within ±20%
CKP1608
Appearance:No significant abnormality
Inductance change: Within ±30%
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±30%
LK1608
LK2125 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
HK0603
Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±20%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
Appearance:No significant abnormality
Inductance change: Within ±10%
MCFE1608
MCKK1608
MCHK2012
MCKK2012
Test Methods and
Remarks
BK、BKP、BKH、LK、CK、CKS、CKP、NM Series、MCF Series:
Temperature :40±2℃
Humidity :90 to 95%RH
Duration :500 +24/-0 hrs
Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1
HK、HKQ、AQ、MC Series:
Temperature :60±2℃
Humidity :90 to 95%RH
Duration :500 +24/-0 hrs
Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1
(Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
15. Loading under Damp Heat
Specified Value
BK0402
Appearance:No significant abnormality
Impedance change: Within ±30
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
CK1608 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
CK2125
CKS2125 Appearance:No significant abnormality
Inductance change: Within ±20%
CKP1608
Appearance:No significant abnormality
Inductance change: Within ±30%
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±30%
LK1608
Appearance:No significant abnormality
Inductance change: 0.047~12.0μH: Within ±10% 15.0~33.0μH: Within ±15%
Q change: Within ±30%
LK2125 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
HK0603
Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±20%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
Appearance:No significant abnormality
Inductance change: Within ±10%
MCFE1608※
MCKK1608※
MCHK2012※
MCKK2012※
Test Methods and
Remarks
BK、BKP、BKH、LK、CK、CKS、CKP、NM Series:
Temperature :40±2℃
Humidity :90 to 95%RH
Applied current :Rated current
Duration :500 +24/-0 hrs
Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1)
HK、HKQ、AQ、MC Series:
Temperature :60±2℃
Humidity :90 to 95%RH
Applied current :Rated current ※MC series ; Idc2max
Duration :500 +24/-0 hrs
Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition."
(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E06R01
16. Loading at High Temperature
Specified Value
BK0402
Appearance:No significant abnormality
Impedance change: Within ±30
BK0603
BK1005
BKH0603
BKH1005
BK1608
BK2125
ARRAY BK2010
BK3216
BKP0402
BKP0603
BKP1005
BKP1608
BKP2125
MCF 0605
Appearance:No significant abnormality
Impedance change: Within ±20
MCF 0806
MCF 1210
MCF 2010
CK1608 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
CK2125
CKS2125 Appearance:No significant abnormality
Inductance change: Within ±20%
CKP1608
Appearance:No significant abnormality
Inductance change: Within ±30%
CKP2012
CKP2016
CKP2520
NM2012
NM2520
LK1005 Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±30%
LK1608
Appearance:No significant abnormality
Inductance change: 0.047~12.0μH: Within ±10% 15.0~33.0μH: Within ±15%
Q change: Within ±30%
LK2125 Appearance:No significant abnormality
Inductance change: Within ±20% Q change: Within ±30%
HK0603
Appearance:No significant abnormality
Inductance change: Within ±10% Q change: Within ±20%
HK1005
HK1608
HK2125
HKQ0402
HKQ0603W
HKQ0603S
HKQ0603U
AQ105
MCFK1608
Appearance:No significant abnormality
Inductance change: Within ±10%
MCFE1608※
MCKK1608※
MCHK2012※
MCKK2012※
Test Methods and
Remarks
Temperature : Maximum operating temperature
Applied current :Rated current ※MC series ; Idc2max
Duration :500 +24/-0 hrs
Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
(See Note 1)
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless
otherwise specified, all the tests are conducted under the "standard condition."
(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E06R01
Precautions on the use of Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils(MC series F type)
Metal Multilayer Chip Power Inductors (MCOILTM MC series)
PRECAUTIONS
1. Circuit Design
Precautions
◆Verification of operating environment, electrical rating and performance
1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social
ramifications.
As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly
differentiated from components used in general purpose applications.
◆Operating Current(Verification of Rated current)
1. The operating current including inrush current for inductors must always be lower than their rated values.
2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect.
2. PCB Design
Precautions
◆Pattern configurations(Design of Land-patterns)
1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used(size of fillet)can directly affect inductor
performance.
Therefore, the following items must be carefully considered in the design of solder land patterns:
(1) The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or
cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder
pads which in turn determines the amount of solder necessary to form the fillets.
(2) When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's
soldering point is separated by solder-resist.
(3) The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to
design land patterns smaller than terminal electrode of chips.
◆Pattern configurations(Inductor layout on panelized[ breakaway PC boards)
1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing
processes (PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered
boards etc.For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to
minimize stress.
Technical
considerations
◆Pattern configurations(Design of Land-patterns)
1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts(larger fillets
which extend above the component end terminations). Examples of improper pattern designs are also shown.
(1) Recommended land dimensions for a typical chip inductor land patterns for PCBs
C
B A B
Chip inductor
Land pattern
Solder-resist
L
W
Chip inductor
Recommended land dimensions for wave-soldering (Unit:mm)
Type 1608 2012 2125 2016 2520 3216
Size L 1.6 2.0 2.0 2.0 2.5 3.2
W 0.8 1.25 1.25 1.6 2.0 1.6
A 0.8~1.0 1.0~1.4 1.0~1.4 1.0~1.4 1.0~1.4 1.8~2.5
B 0.5~0.8 0.8~1.5 0.8~1.5 0.8~1.5 0.6~1.0 0.8~1.7
C 0.6~0.8 0.9~1.2 0.9~1.2 1.3~1.6 1.6~2.0 1.2~1.6
Recommended land dimensions for reflow-soldering (Unit:mm)
Type 0402 0603 1005 105 1608 2012 2125 2016 2520 3216
Size L 0.4 0.6 1.0 1.0 1.6 2.0 2.0 2.0 2.5 3.2
W 0.2 0.3 0.5 0.6 0.8 1.25 1.25 1.6 2.0 1.6
A 0.15~0.25 0.20~0.30 0.45~0.55 0.50~0.55 0.81.0 0.81.2 0.81.2 0.8~1.2 1.0~1.4 1.8~2.5
B 0.10~0.20 0.20~0.30 0.40~0.50 0.30~0.40 0.60.8 0.81.2 0.81.2 0.8~1.2 0.6~1.0 0.6~1.5
C 0.15~0.30 0.25~0.40 0.45~0.55 0.60~0.70 0.60.8 0.91.6 0.91.6 1.2~2.0 1.8~2.2 1.2~2.0
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E06R01
Excess solder can affect the ability of chips to withstand mechanical stresses. Therefore, please take proper precautions when
designing land-patterns.
d
c
a
b
a
d
c
a
b
a
Recommended land dimension for Reflow-soldering
Type 3216 2010 1210 0806 0605
Size L 3.2 2.0 1.25 0.85 0.65
W 1.6 1.0 1.0 0.65 0.50
a 0.7~0.9 0.5~0.6 0.45~0.55 0.25~0.35 0.27~0.33
b 0.8~1.0 0.5~0.6 0.7~0.8 0.25~0.35 0.17~0.23
c 0.4~0.5 0.2~0.3 0.25~0.35 0.25~0.35 0.20~0.26
d 0.8 0.5 0.55 0.5 0.4
(Unit:mm)
((2) Examples of good and bad solder application
Item Not recommended Recommended
Mixed mounting of SMD and
leaded components
Lead wire of component
Solder-resist
Component placement close to
the chassis
Chassis
Solder (for grounding)
Electrode pattern
Solder-resist
Hand-soldering of leaded
components near mounted
components
Soldering iron
Lead wire of component
Solder-resist
Horizontal component
placement
Solder-resist
◆Pattern configurations(Inductor layout on panelized[ breakaway PC boards)
1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical
stresses from board warp or deflection.
Item Not recommended Recommended
Deflection of the board
Position the component at a
right angle to the direction of
the mechanical stresses that
are anticipated.
1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary
depending on inductor layout.
An example below should be counted for better design.
E
D
C
A B
Slit
Magnitude of stress A>B=C>D>E
Perforation
1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the
method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and
perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E06R01
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards.
2. The maintenance and inspection of the mounter should be conducted periodically.
◆Selection of Adhesives
1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics
unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening
temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and
amounts of adhesive to use.
Technical
considerations
◆Adjustment of mounting machine
1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the
following points should be considered before lowering the pick-up nozzle:
(1) The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the
board.
(2) The pick-up pressure should be adjusted between 1 and 3N static loads.
(3) To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be
used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement:
Item Improper method Proper method
Single-sided mounting
chipping
or cracking
supporting pins
or back-up pins
Double-sided mounting
chipping
or cracking
supporting pins
or back-up pins
2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical
impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance,
inspection and replacement of the pin should be conducted periodically.
◆Selection of Adhesives
1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of
the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the
board may adversely affect component placement, so the following precautions should be noted in the application of adhesives.
(1) Required adhesive characteristics
a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process.
b. The adhesive should have sufficient strength at high temperatures.
c. The adhesive should have good coating and thickness consistency.
d. The adhesive should be used during its prescribed shelf life.
e. The adhesive should harden rapidly.
f. The adhesive must not be contaminated.
g. The adhesive should have excellent insulation characteristics.
h. The adhesive should not be toxic and have no emission of toxic gasses.
(2) When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect
component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much
adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad.
[Recommended conditions]
Figure 0805 case sizes as examples
a 0.3mm min
b 100~120μm
c Area with no adhesive
Amount of adhesives
a a
b
After inductors are bonded
c c
4. Soldering
Precautions
◆Selection of Flux
1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use;
(1) Flux used should be with less than or equal to 0.1 wt% Chlorine conversion method of halogenated content. Flux having a strong
acidity content should not be applied.
(2) When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level.
(3) When using water-soluble flux, special care should be taken to properly clean the boards.
◆Soldering
1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us
about peak temperature when you use lead-free paste.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E06R01
Technical
considerations
◆Selection of Flux
1-1. When too much halogenated substance(Chlorine, etc.)content is used to activate the flux, or highly acidic flux is used, an excessive
amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the
surface of the Inductor.
1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may
detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high
humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The
cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux.
◆Soldering
1-1. Preheating when soldering
Heating: Chip inductor components should be preheated to within 100 to 130℃ of the soldering. Cooling: The temperature difference
between the components and cleaning process should not be greater than 100℃.
Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the
soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal
shock.
[Reflow soldering]
【Recommended conditions for eutectic soldering】
【Recommended condition for Pb-free soldering】
Preheating 230℃
Within 10sec.
Slow cooling
60sec.
Min.
60sec
Min.
300
200
100
0
Temperature(℃)
Peak
260℃ Max.
Within 10sec.
Slow
cooling
Heating above
230℃
40sec. Max.
300
200
100
0
Temperature(℃)
Preheating150℃
60sec. Min.
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be reflow soldering for 2 times.
MC series; Peak 230 (eutectic soldering) 260 (Pb-free soldering)max
within 5sec.
Caution
1. The ideal condition is to have solder mass(fillet)controlled to 1/2 to 1/3 of the thickness of the inductor, as shown
below:
1/2T~1/3T
PC board
Solder
Inductor
T
2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to
recommended times as possible.
[Wave soldering]
【Recommended conditions for eutectic soldering】
【Recommended condition for Pb-free soldering】
230~250℃
Within 3sec.
Slow cooling
Preheating
120sec. Min.
300
200
100
0
Temperature(℃)
Peak
260℃ Max.
Within 10sec.
Slow
cooling
120sec. Min.
300
200
100
0
Temperature(℃)
Preheating
150℃
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be wave soldering for 1 time.
※Except for reflow soldering type.
Caution
1. Make sure the inductors are preheated sufficiently.
2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130℃.
3. Cooling after soldering should be as gradual as possible.
4. Wave soldering must not be applied to the inductors designated as for reflow soldering only.
[Hand soldering]
【Recommended conditions for eutectic soldering
【Recommended condition for Pb-free soldering】
230~280℃
Within 3sec.
Slow cooling
Preheating
60sec. Min.
400
200
100
0
Temperature(℃)
300
Peak
350℃ Max.
Within 3sec.
Slow cooling
⊿T
400
200
100
0
Temperature(℃)
Preheating
150℃ Min.
60sec. Min.
300
(※⊿T≦190℃( 3216Type max), ⊿T≦130℃( 3225 Type min)
※It is recommended to use 20W soldering iron and the tip is 1φ or less.
※The soldering iron should not directly touch the components.
※Assured to be soldering iron for 1 time.
Note: The above profiles are the maximum allowable soldering condition, therefore
these profiles are not always recommended.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E06R01
Caution
1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm.
2. The soldering iron should not directly touch the inductor.
5. Cleaning
Precautions
◆Cleaning conditions
1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux
used and purpose of the cleaning(e.g. to remove soldering flux or other materials from the production process.)
2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's
characteristics.
Technical
considerations
◆Cleaning conditions
1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation
of the inductor's electrical properties(especially insulation resistance).
2. Inappropriate cleaning conditions(insufficient or excessive cleaning)may detrimentally affect the performance of the inductors.
(1) Excessive cleaning
a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the
cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions
should be carefully checked;
Ultrasonic output Below 20W/
Ultrasonic frequency Below 40kHz
Ultrasonic washing period 5 min. or less
6. Post cleaning processes
Precautions
◆Application of resin coatings, moldings, etc. to the PCB and components.
1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the inductor's performance.
2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat
may lead to inductor damage or destruction.
3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
Precautions
◆Breakaway PC boards(splitting along perforations)
1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection
or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆General handling precautions
1. Always wear static control bands to protect against ESD.
2. Keep the inductors away from all magnets and magnetic objects.
3. Use non-magnetic tweezers when handling inductors.
4. Any devices used with the inductors( soldering irons, measuring instruments) should be properly grounded.
5. Keep bare hands and metal products(i.e., metal desk)away from chip electrodes or conductive areas that lead to chip electrodes.
6. Keep inductors away from items that generate magnetic fields such as speakers or coils.
◆Mechanical considerations
1. Be careful not to subject the inductors to excessive mechanical shocks.
(1) If inductors are dropped on the floor or a hard surface they should not be used.
(2) When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other
boards or components.
8. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・Recommended conditions
Ambient temperature: Below 30℃ Humidity: Below 70% RH
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of inductor is deteriorated as time
passes, so inductors should be used within 6 months from the time of delivery.
・Inductor should be kept where no chlorine or sulfur exists in the air.
Technical
considerations
◆Storage
1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within
6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors.

Products

FERRITE BEAD 1 KOHM 0402 1LN
Available Quantity75766
Unit Price12
FERRITE BEAD 600 OHM 0805 1LN
Available Quantity49681
Unit Price12
FERRITE BEAD 600 OHM 0603 1LN
Available Quantity69430
Unit Price12
FERRITE BEAD 2.5 KOHM 0603 1LN
Available Quantity29598
Unit Price12
FERRITE BEAD 47 OHM 0805 1LN
Available Quantity251234
Unit Price14
FERRITE BEAD 100 OHM 0805 1LN
Available Quantity37301
Unit Price14
FERRITE BEAD 1 KOHM 0201 1LN
Available Quantity19581
Unit Price12
FERRITE BEAD 120 OHM 0201
Available Quantity25453
Unit Price12
FERRITE BEAD 600 OHM 0402 1LN
Available Quantity107820
Unit Price12
FERRITE BEAD 10 OHM 0402 1LN
Available Quantity80318
Unit Price12
FERRITE BEAD 120 OHM 0402 1LN
Available Quantity47535
Unit Price12
FERRITE BEAD 600 OHM 0402 1LN
Available Quantity46245
Unit Price12
FERRITE BEAD 600 OHM 0402 1LN
Available Quantity44305
Unit Price12
FERRITE BEAD 120 OHM 0402 1LN
Available Quantity21264
Unit Price12
FERRITE BEAD 240 OHM 0402 1LN
Available Quantity48189
Unit Price12
FERRITE BEAD 1.8 KOHM 0402 1LN
Available Quantity1930379
Unit Price12
FERRITE BEAD 1.5 KOHM 0402 1LN
Available Quantity475538
Unit Price12
FERRITE BEAD 1 KOHM 0402 1LN
Available Quantity31329
Unit Price12
FERRITE BEAD 1 KOHM 0603 1LN
Available Quantity46658
Unit Price12
FERRITE BEAD 1 KOHM 0603 1LN
Available Quantity29139
Unit Price12